The problem persists in my system. The second card reports no clock. However, the devices attached to it work consistently and I don't get regular IRQ misses anymore. I say regular because with RH8 IRQ misses for the new card would show up all the time. Now they only occur under heavy network activity, such as copying a very large file from another server.
Fernando
On Dec 3, 2004, at 6:57 PM, Kevin Blackham wrote:
List,
I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there.
The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to legacy PBX. Clock is received from telco, old PBX receives clock from zaptel card, everything's green there, but the other card, the T100P, seems to not send any timing at all, as verified by our T1 analyzer, and is persistently in red alarm. In fact, even if I stick a loopback plug in the T100P, the alarm persists (loopback causes a result in the TE410P). The T100P and channel bank were just pulled from another working * box, and the configuration is nearly identical, except it was the only T1 interface.
System: Supermicro dual Xeon 2.4, both cards on same PCI bus. Cards: one T100P, one TE410P. Config: spans 1-4 for quad card (module loaded first), span 5 is single port card Channel bank: Access Bank II, 12 FXS
Info dumps (some snipped for brevity)
lspci (snipped, these are the only devices on bus 5): 0000:05:02.0 Network controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface 0000:05:03.0 Communication controller: Xilinx Corporation: Unknown device 0314 (rev 01)
cat /proc/interrupts (odd, shouldn't the T100P be generating 1000 ints/sec?):
CPU0 CPU1 CPU2 CPU3
0: 20727 0 18569488 0 IO-APIC-edge timer
9: 0 0 0 0 IO-APIC-level acpi
28: 177705 0 0 0 IO-APIC-level eth0
29: 9282 0 0 0 IO-APIC-level eth1
72: 35845 0 0 0 IO-APIC-level dpti0
100: 102 0 0 0 IO-APIC-level t1xxp
104: 18342391 0 0 0 IO-APIC-level t4xxp
lsmod: Module Size Used by wct1xxp 17568 0 wct4xxp 70048 0 zaptel 226436 222 wct1xxp,wct4xxp e1000 87348 0 crc_ccitt 3072 1 zaptel
zaptel.conf: span=1,1,0,esf,b8zs span=2,2,0,esf,b8zs span=3,3,0,esf,b8zs span=4,4,0,esf,b8zs span=5,0,0,esf,b8zs bchan=1-23 dchan=24 bchan=25-47 dchan=48 bchan=49-71 dchan=72 bchan=73-95 dchan=96 fxoks=97-108 #fxoks=109-120 loadzone = us defaultzone=us
asterisk/zapata.conf: [channels] language=en echocancel=yes echocancelwhenbridged=no echotraining=yes echotraining=800 immediate=no ;--pstn-- context=from-pstn signalling=pri_cpe switchtype=dms100 group = 1 channel => 1-23,25-47,49-71 ;--pri to pbx-- signalling=pri_net switchtype=dms100 group = 3 channel => 73-95 ;--channel bank-- context=fax+modem signalling=fxo_ks channel => 97-108
a snippet from dmesg: ACPI: PCI interrupt 0000:05:03.0[A] -> GSI 104 (level, low) -> IRQ 104 Found TE410P at base address f8401000, remapped to f9b98000 TE410P version c01a009b FALC version: 00000005, Board ID: 00 <registers snipped> TE410P: Launching card: 0 TE410P: Setting up global serial parameters Found a Wildcard: Wildcard TE410P-Xilinx ACPI: PCI interrupt 0000:05:02.0[A] -> GSI 100 (level, low) -> IRQ 100 Framer: DS21552, Revision: 3 (T1) Found a Wildcard: Digium Wildcard T100P T1/PRI Registered tone zone 0 (United States / North America) TE410P: Span 1 configured for ESF/B8ZS SPAN 1: Primary Sync Source TE410P: Span 2 configured for ESF/B8ZS SPAN 2: Secondary Sync Source TE410P: Span 3 configured for ESF/B8ZS SPAN 3: Tertiary Sync Source TE410P: Span 4 configured for ESF/B8ZS SPAN 4: Quaternary Sync Source Using ESF/B8ZS coding/framing Calling startup (flags is 4099) _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
