zaptel.conf has one pri_cpe and one pri_net
I see the calls being made but no "connecting" message. show channels
shows the one call in Ring state and never getting connected.
topbx*CLI> show channels
Channel Location State Application(Data)
0 active channels
0 active calls
-- Executing Dial("SIP/7046-052dafd0", "Zap/G0/300|45") in new stack
-- Requested transfer capability: 0x00 - SPEECH
-- Called G0/300
-- Accepting call from '7046' to '300' on channel 0/23, span 2
-- Executing Answer("Zap/47-1", "") in new stack
-- Executing MusicOnHold("Zap/47-1", "") in new stack
-- Started music on hold, class 'default', on Zap/47-1
-- Zap/23-1 is proceeding passing it to SIP/7046-052dafd0
topbx*CLI> show channels
Channel Location State Application(Data)
Zap/47-1 [EMAIL PROTECTED]:2 Up MusicOnHold()
Zap/23-1 [EMAIL PROTECTED]:1 Dialing AppDial((Outgoing Line))
SIP/7046-052dafd0 [EMAIL PROTECTED]:1 Ring Dial(Zap/G0/300|45)
3 active channels
2 active calls
-- Nobody picked up in 45000 ms
-- Hungup 'Zap/23-1'
-- Channel 0/23, span 2 got hangup request, cause 16
topbx*CLI> show channels
Channel Location State Application(Data)
Zap/47-1 [EMAIL PROTECTED]:2 Up MusicOnHold()
SIP/7046-052dafd0 [EMAIL PROTECTED]:2 Ring (None)
2 active channels
2 active calls
-- Timeout on SIP/7046-052dafd0
== CDR updated on SIP/7046-052dafd0
-- Executing Hangup("SIP/7046-052dafd0", "") in new stack
== Spawn extension (esi-toronto, t, 1) exited non-zero on
'SIP/7046-052dafd0'
topbx*CLI> show channels
Channel Location State Application(Data)
Zap/47-1 [EMAIL PROTECTED]:2 Up MusicOnHold()
1 active channel
1 active call
topbx*CLI>
/var/log/asterisk/cdr-csv/Master.csv
"","7046","t","esi-toronto","""device""
<7046>","SIP/7046-1bf3ea20","Zap/23-1","Hangup","","2007-07-04
11:13:40",,"2007-07-04 11:14:35",55,0,"NO ANSWER","DOCUMENTATION"
McQuiggan, Mark - Broadridge (Toronto) wrote:
David:
What's you zaptel.conf say? Are both groups set to pri_net or pri_cpe
signalling? You'll need that for a crossover cable...
Thanks,
Mark.
Please note: Effective April 1, my e-mail address is
[EMAIL PROTECTED]
-----Original Message-----
From: David Cook [mailto:[EMAIL PROTECTED]
Sent: Tuesday, July 03, 2007 1:57 PM
To: [email protected]
Subject: [on-asterisk] Calls not connecting on PRI span
Here is an interesting support problem.
New A102D card. Span 0/1 tied with a cross over cable (to test).
Dial an extension out one span
exten => _30X,1,Dial(Zap/G0/${EXTEN},45)
Should dial out on last channel of group 0 and should arrive on last
channel of group 1 (other span)
[from-internal]
; inbound from (group 1) Nortel defaults to pass-thru to PSTN
; pstn on trunk group 0, descending order
exten => _.,1,MusiconHold()
I should hear music. However I get no connection ... Last message is
"proceeding" below, no ringing yet the channel (47-1) won't hangup.
It's like it doesn't know to connect the two legs of the call!!
-- Executing [EMAIL PROTECTED]:1] Dial("SIP/7046-1bebd770",
"Zap/G0/300|45") in new stack
-- Requested transfer capability: 0x00 - SPEECH
-- Called G0/300
-- Accepting call from '7046' to '300' on channel 0/23, span 2
-- Executing [EMAIL PROTECTED]:1] MusicOnHold("Zap/47-1", "") in
new stack
-- Started music on hold, class 'default', on Zap/47-1
-- Zap/23-1 is proceeding passing it to SIP/7046-1bebd770
topbx*CLI>
Asterisk 1.4.5
Zaptel 1.4.3
Sangoma Wanpipe 2.3.4-10
Any ideas??
dbc.
--
David Cook
---------------------------------------------------------------------
To unsubscribe, e-mail: [EMAIL PROTECTED]
For additional commands, e-mail: [EMAIL PROTECTED]
This message and any attachments are intended only for the use of the addressee
and
may contain information that is privileged and confidential. If the reader of the
message is not the intended recipient or an authorized representative of the
intended recipient, you are hereby notified that any dissemination of this
communication is strictly prohibited. If you have received this communication in
error, please notify us immediately by e-mail and delete the message and any
attachments from your system.
