Hi, I'm using the Ubuntu software from Robert Nelson.
Micka, On Wed, Oct 23, 2013 at 5:11 PM, Hieu Duong <hieuduong....@gmail.com> wrote: > Micka, > > I did not see any issue with the GPIO-mapped buttons on LCD7 rev A3 when > using with latest Angstrom factory software 2013-09-04. The offset is also > 0x154. Could you confirm which software you are using? > > -Hieu > > > > > On Tuesday, October 22, 2013 10:18:36 AM UTC-5, Mickae1 wrote: > >> A correction to my mail, normally it should be 0x154, which was the case >> before : >> >> bone_lcd7_cape_keys_00A3_pins: pinmux_bone_lcd7_cape_keys_**00A3_pins { >> pinctrl-single,pins = < >> 0x040 0x2f /* KEY_LEFT gpmc_a0.gpio1_16, INPUT | PULLDIS | MODE7 */ >> 0x044 0x2f /* KEY_RIGHT gpmc_a1.gpio1_17, INPUT | PULLDIS | MODE7 */ >> 0x04c 0x2f /* KEY_UP gpmc_a3.gpio1_19, INPUT | PULLDIS | MODE7 */ >> 0x198 0x2f /* KEY_DOWN mcasp0_axr0.gpio3_16, INPUT | PULLDIS | MODE7 */ >> *0x154 0x2f /* KEY_ENTER spi0_d0.gpio0_3, INPUT | PULLDIS | MODE7 */* >> >; >> }; >> >> >> >> >> On Tue, Oct 22, 2013 at 4:45 PM, Micka <micka...@gmail.com> wrote: >> >>> Hi, >>> >>> I wanted to signal an error ( or not, but I double checked ) : >>> >>> >>> The Key ENTER of the LCD7 cap Rev A3 is connected to the GPIO0_3 >>> => https://github.com/**CircuitCo/BeagleBone-LCD7-** >>> RevA3/blob/master/BeagleBone-**LCD7-RevA3-schematic.pdf?raw=**true<https://github.com/CircuitCo/BeagleBone-LCD7-RevA3/blob/master/BeagleBone-LCD7-RevA3-schematic.pdf?raw=true> >>> >>> But In the last updated version of the file BB-BONE-LCD7-01-00A3.dts , I >>> got : >>> >>> >>> >>> 0x040 0x2f /* KEY_LEFT gpmc_a0.gpio1_16, INPUT | PULLDIS | MODE7 */ >>> 0x044 0x2f /* KEY_RIGHT gpmc_a1.gpio1_17, INPUT | PULLDIS | MODE7 */ >>> 0x04c 0x2f /* KEY_UP gpmc_a3.gpio1_19, INPUT | PULLDIS | MODE7 */ >>> 0x198 0x2f /* KEY_DOWN mcasp0_axr0.gpio3_16, INPUT | PULLDIS | MODE7 */ >>> *0x070 0x2f /* KEY_ENTER gpmc_wait0.gpio0_3, INPUT | PULLDIS | MODE7 */* >>> >>> >>> >>> Which is normally 0x954 and not 0x070 ( 0x070 is for GPIO0_30 ) >>> >>> >>> So, am I right or wrong ? If I'm wrong, why in june, july, ... the >>> address of uart4_rx was 0x070, which is GPIO0_30 ? >>> >>> >>> >>> >>> >>> Micka, >>> >> >> -- > For more options, visit http://beagleboard.org/discuss > --- > You received this message because you are subscribed to the Google Groups > "BeagleBoard" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to beagleboard+unsubscr...@googlegroups.com. > For more options, visit https://groups.google.com/groups/opt_out. > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to beagleboard+unsubscr...@googlegroups.com. For more options, visit https://groups.google.com/groups/opt_out.