Yes I did Gerald. I removed the power supply then only I removed the sd card and gave power to it again. I have already flashed my eMMC once as soon as a bought it last week as I ran into boot problem as I deleted some file during date time update. At that time it worked, so I know the flashing process. I was running ubuntu precise from my sd card, and I was trying to use the leftover space available in the sd card by following the guide in the following web link: http://elinux.org/Beagleboard:Expanding_File_System_Partition_On_A_microSD, only after doing this, I ran into the booting issue that I am not able to fix. Thanks in advance for your reply.
On Tuesday, 14 January 2014 19:17:37 UTC+5:30, Gerald wrote: > > After the flashing did you remove the power from the board as instructed? > > http://www.elinux.org/Beagleboard:Updating_The_Software > > Gerald > > > > On Tue, Jan 14, 2014 at 2:50 AM, Jay <[email protected] <javascript:> > > wrote: > >> My BBB doesn't boot, I tried flashing it with factory Angstrom image >> available at beagleboard.org website. The 4 LEDs light up and the >> process is completed. But doesn't boot even after that. To see what is >> happening I connected my Serial to USB converter to the BBB and using Putty >> I saw the U-Boot message which appears like the following: >> >> U-Boot SPL 2013.04-dirty (Jul 10 2013 - 14:02:53) >> >> timed out in wait_for_pin: I2C_STAT=0 >> >> Could not probe the EEPROM; something fundamentally wrong on the I2C bus. >> >> Could not get board ID. >> >> Unknown board, assuming Beaglebone LT/Black.musb-hdrc: ConfigData=0xde >> (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) >> >> musb-hdrc: MHDRC RTL version 2.0 >> >> musb-hdrc: setup fifo_mode 4 >> >> musb-hdrc: 28/31 max ep, 16384/16384 memory >> >> USB Peripheral mode controller at 47401000 using PIO, IRQ 0 >> >> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, >> SoftConn) >> >> musb-hdrc: MHDRC RTL version 2.0 >> >> musb-hdrc: setup fifo_mode 4 >> >> musb-hdrc: 28/31 max ep, 16384/16384 memory >> >> USB Host mode controller at 47401800 using PIO, IRQ 0 >> >> OMAP SD/MMC: 0 >> >> mmc_send_cmd : timeout: No status update >> >> reading u-boot.img >> >> reading u-boot.img >> >> >> >> >> >> U-Boot 2013.04-dirty (Jul 10 2013 - 14:02:53) >> >> >> >> I2C: ready >> >> DRAM: 512 MiB >> >> WARNING: Caches not enabled >> >> timed out in wait_for_pin: I2C_STAT=0 >> >> Could not probe the EEPROM; something fundamentally wrong on the I2C bus. >> >> Could not get board ID. >> >> NAND: No NAND device found!!! >> >> 0 MiB >> >> MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 >> >> *** Warning - readenv() failed, using default environment >> >> >> >> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, >> SoftConn) >> >> musb-hdrc: MHDRC RTL version 2.0 >> >> musb-hdrc: setup fifo_mode 4 >> >> musb-hdrc: 28/31 max ep, 16384/16384 memory >> >> USB Peripheral mode controller at 47401000 using PIO, IRQ 0 >> >> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, >> SoftConn) >> >> musb-hdrc: MHDRC RTL version 2.0 >> >> musb-hdrc: setup fifo_mode 4 >> >> musb-hdrc: 28/31 max ep, 16384/16384 memory >> >> USB Host mode controller at 47401800 using PIO, IRQ 0 >> >> Net: <ethaddr> not set. Validating first E-fuse MAC >> >> cpsw, usb_ether >> >> Hit any key to stop autoboot: 0 >> >> gpio: pin 53 (gpio 53) value is 1 >> >> Card did not respond to voltage select! >> >> mmc0(part 0) is current device >> >> Card did not respond to voltage select! >> >> No micro SD card found, setting mmcdev to 1 >> >> mmc_send_cmd : timeout: No status update >> >> mmc1(part 0) is current device >> >> gpio: pin 54 (gpio 54) value is 1 >> >> SD/MMC found on device 1 >> >> reading uEnv.txt >> >> 26 bytes read in 3 ms (7.8 KiB/s) >> >> Loaded environment from uEnv.txt >> >> Importing environment from mmc ... >> >> gpio: pin 55 (gpio 55) value is 1 >> >> 4385024 bytes read in 768 ms (5.4 MiB/s) >> >> gpio: pin 56 (gpio 56) value is 1 >> >> 24808 bytes read in 54 ms (448.2 KiB/s) >> >> Booting from mmc ... >> >> ## Booting kernel from Legacy Image at 80007fc0 ... >> >> Image Name: Angstrom/3.8.13/beaglebone >> >> Image Type: ARM Linux Kernel Image (uncompressed) >> >> Data Size: 4384960 Bytes = 4.2 MiB >> >> Load Address: 80008000 >> >> Entry Point: 80008000 >> >> Verifying Checksum ... OK >> >> ## Flattened Device Tree blob at 80f80000 >> >> Booting using the fdt blob at 0x80f80000 >> >> XIP Kernel Image ... OK >> >> OK >> >> Using Device Tree in place at 80f80000, end 80f890e7 >> >> >> >> Starting kernel ... >> >> >> >> Uncompressing Linux... done, booting the kernel. >> >> [ 1.148261] omap_i2c 44e0b000.i2c: controller timed out >> >> [ 1.148304] tps65217 0-0024: Failed to read INT reg >> >> [ 1.148322] tps65217 0-0024: Failed to probe pwr_but >> >> [ 2.148252] omap_i2c 44e0b000.i2c: controller timed out >> >> [ 3.152151] omap_i2c 44e0b000.i2c: controller timed out >> >> [ 3.182788] omap2_mbox_probe: platform not supported >> >> [ 4.246560] omap_i2c 44e0b000.i2c: controller timed out >> >> [ 5.254176] omap_i2c 44e0b000.i2c: controller timed out >> >> [ 6.767826] omap_i2c 44e0b000.i2c: controller timed out >> >> [ 7.779563] omap_i2c 44e0b000.i2c: controller timed out >> >> [ 9.293213] omap_i2c 44e0b000.i2c: controller timed out >> >> [ 10.305060] omap_i2c 44e0b000.i2c: controller timed out >> >> [ 11.818596] omap_i2c 44e0b000.i2c: controller timed out >> >> [ 12.830340] omap_i2c 44e0b000.i2c: controller timed out >> >> >> Similarly when I try to boot the board using Ubuntu on SD Card I see the >> following message: >> >> ▒m▒▒▒▒`▒▒▒`rpqsnqpmpprtym▒qu▒u▒▒▒`h▒▒▒`qw@rpqs`m`qvzsuzqqi >> >> i2c_probe: pads on bus 0 probably not configured (status=0x10) >> >> Could not probe the EEPROM; something fundamentally wrong on the I2C bus. >> >> Could not get board ID. >> >> i2c_probe: pads on bus 0 probably not configured (status=0x10) >> >> Could not probe the EEPROM; something fundamentally wrong on the I2C bus. >> >> Could not get board ID. >> >> Unknown board, cannot configure pinmux.### ERROR ### Please RESET the >> board ### >> __ >> >> Can any of you Guys figure out what is the problem? and how to fix it? >> Thanks in Advance for your solution. >> >> -- >> For more options, visit http://beagleboard.org/discuss >> --- >> You received this message because you are subscribed to the Google Groups >> "BeagleBoard" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected] <javascript:>. >> For more options, visit https://groups.google.com/groups/opt_out. >> > > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/groups/opt_out.
