Hello I would really like any kind of suggestion. I am stuck at this error for last quiet a days.
any idea please?? On Tuesday, August 1, 2017 at 10:45:06 AM UTC+5:30, Jitendriya Parida wrote: > > Hello > > I am very new to JTAG and i am trying to do the setup for jtag in > beaglebone black(BBB) rev c board using buspirate(BP) and openocd. > I have installed the P2 header in BBB manually. I have connected the BBB > and BP as follows > > JTAG > > BP > > BBB > > TMS > > CS > > P2(1) P2 header pin 1 > > TDI > > MOSI > > P2(3) > > VTREF > > VPU > > P2(5) > > TDO > > MISO > > P2(7) > > TCK > > CLK > > P2(11) > > TRST > > AUX > > P2(2) > > GRND > > GND > > P2(10) > > > > I am using my user configuration file(BP_userconfig.cfg) for openocd which > has following content. > > source [find interface/buspirate.cfg] > > buspirate_vreg 0 > buspirate_mode open-drain > buspirate_pullup 1 > reset_config srst_only > buspirate_port /dev/ttyUSB0 > > source [find board/ti_beaglebone_black.cfg] > > Now while running the command *sudo openocd -f BP_userconfig.cfg* I am > getting following error. > > > > > > > > > > > > > > > > > > > > *lenova@lenova-ThinkPad-T410:~/jiten/JTAG$ sudo openocd -f > BP_userconfig.cfg Open On-Chip Debugger 0.10.0+dev-00167-g29cfe9c > (2017-07-20-14:08) Licensed under GNU GPL v2 For bug reports, read > http://openocd.org/doc/doxygen/bugs.html > <http://openocd.org/doc/doxygen/bugs.html> Warn : Adapter driver > 'buspirate' did not declare which transports it allows; assuming legacy > JTAG-only Info : only one transport option; autoselect 'jtag' srst_only > separate srst_gates_jtag srst_open_drain connect_deassert_srst > trst_and_srst separate srst_gates_jtag trst_push_pull srst_open_drain > connect_deassert_srst adapter speed: 1000 kHz trst_and_srst separate > srst_gates_jtag trst_push_pull srst_open_drain connect_deassert_srst Info : > Buspirate Interface ready! Info : This adapter doesn't support configurable > speed Info : JTAG tap: am335x.jrc tap/device found: 0x2b94402f (mfg: 0x017 > (Texas Instruments), part: 0xb944, ver: 0x2) Info : JTAG tap: am335x.dap > enabled Error: JTAG-DP STICKY ERROR Error: Could not initialize the APB-AP > *Does > anyone have any idea about this error? and do i need to do anything else in > BBB apart from installing P2 header? > Please let me know if i am doing anything wrong. > > Thanks in advance. > > Regards > jitendriya > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/e8b15735-9efe-40c9-bc6f-c2ecf5776eb4%40googlegroups.com. For more options, visit https://groups.google.com/d/optout.
