This may be a long shot, but I just saw a reference to openocd over on the TI E2E CCS support pages:
https://e2e.ti.com/support/development_tools/code_composer_studio/f/81/p/522774/1904904 If you try posting over there about your Open OCD issues, you may have more luck than here... On Thursday, August 3, 2017 at 9:46:10 AM UTC-5, Jeff Andich wrote: > > If there's a reason why you need to stick with openocd, are there other > forums, http://openocd.org/discussion/forum/, where you can post up on > the messages you are seeing? > > I'm currently attempting JTAG debugging of the Linux SPL on the > am572xEVM/BeagleBoard-X15 platform using CCS 7.2 (running under an Ubuntu > VM) and XDS100V2. > > Even though I'm a newbie, if you were to use CCS7 + the Blackhawk debugger > (XDS100V2), maybe people in my shoes on this forum would have already > encountered some errors that you see, and potentially be able to provide > tips.. > > CCS 7 is free and XDS100V2 is like $100.00. > > Plus in addition to this site, there's a CCS forum on TI e2e, > > https://e2e.ti.com/support/development_tools/code_composer_studio/f/81?tisearch=e2e-sitesearch&keymatch=code%20composer%20studio%20forum > , > > But last I checked, for Linux they support TI SDK images and not > BeagleBoard.org images.. > But if you're just trying to get started with CCS and XDS100V2, they may > be able to walk you through > some of your issues. > > > > > On Tuesday, August 1, 2017 at 12:15:06 AM UTC-5, Jitendriya Parida wrote: > >> Hello >> >> I am very new to JTAG and i am trying to do the setup for jtag in >> beaglebone black(BBB) rev c board using buspirate(BP) and openocd. >> I have installed the P2 header in BBB manually. I have connected the BBB >> and BP as follows >> >> JTAG >> >> BP >> >> BBB >> >> TMS >> >> CS >> >> P2(1) P2 header pin 1 >> >> TDI >> >> MOSI >> >> P2(3) >> >> VTREF >> >> VPU >> >> P2(5) >> >> TDO >> >> MISO >> >> P2(7) >> >> TCK >> >> CLK >> >> P2(11) >> >> TRST >> >> AUX >> >> P2(2) >> >> GRND >> >> GND >> >> P2(10) >> >> >> >> I am using my user configuration file(BP_userconfig.cfg) for openocd >> which has following content. >> >> source [find interface/buspirate.cfg] >> >> buspirate_vreg 0 >> buspirate_mode open-drain >> buspirate_pullup 1 >> reset_config srst_only >> buspirate_port /dev/ttyUSB0 >> >> source [find board/ti_beaglebone_black.cfg] >> >> Now while running the command *sudo openocd -f BP_userconfig.cfg* I am >> getting following error. >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> *lenova@lenova-ThinkPad-T410:~/jiten/JTAG$ sudo openocd -f >> BP_userconfig.cfg Open On-Chip Debugger 0.10.0+dev-00167-g29cfe9c >> (2017-07-20-14:08) Licensed under GNU GPL v2 For bug reports, read >> http://openocd.org/doc/doxygen/bugs.html >> <http://openocd.org/doc/doxygen/bugs.html> Warn : Adapter driver >> 'buspirate' did not declare which transports it allows; assuming legacy >> JTAG-only Info : only one transport option; autoselect 'jtag' srst_only >> separate srst_gates_jtag srst_open_drain connect_deassert_srst >> trst_and_srst separate srst_gates_jtag trst_push_pull srst_open_drain >> connect_deassert_srst adapter speed: 1000 kHz trst_and_srst separate >> srst_gates_jtag trst_push_pull srst_open_drain connect_deassert_srst Info : >> Buspirate Interface ready! Info : This adapter doesn't support configurable >> speed Info : JTAG tap: am335x.jrc tap/device found: 0x2b94402f (mfg: 0x017 >> (Texas Instruments), part: 0xb944, ver: 0x2) Info : JTAG tap: am335x.dap >> enabled Error: JTAG-DP STICKY ERROR Error: Could not initialize the APB-AP >> *Does >> anyone have any idea about this error? and do i need to do anything else in >> BBB apart from installing P2 header? >> Please let me know if i am doing anything wrong. >> >> Thanks in advance. >> >> Regards >> jitendriya >> > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/9dad41be-1b32-4bd0-9d06-12bcdf38255f%40googlegroups.com. For more options, visit https://groups.google.com/d/optout.
