Still getting access denied on the picture. You should only need to pull the shell that covers the sides and back. It is held in place by five screws. One on the back lower section, and two on each side towards the front. On the sides there's one and one low.
Once that's off, hopefully you'll be able to reach in from the right side and move the OPV around to where you need it. Obviously, be sure the machine is unplugged before you do this. If you can't adjusted from there, then you may need to go further into disassembling the machine, but don't worry about that for now. bmc Sent from my 8-track deck On Mar 5, 2012, at 21:11, Japheth Lim <[email protected]> wrote: > Uploaded the photo on tumblr (http://s3.amazonaws.com/data.tumblr.com/ > tumblr_m0g6b0xIwb1qbsusgo1_1280.jpg? > AWSAccessKeyId=AKIAJ6IHWSU3BX3X7X3Q&Expires=1331096959&Signature=UDXYGaMLk2DOyqVVcm2klMOkQLs > %3D); can you get to it now? > > And how do I pull the cover? Do I do that by unscrewing the screws on > the front panel, or do I actually have to open the machine up? > > On Mar 5, 1:00 am, Ben McCafferty <[email protected]> wrote: >> Can't get to the photo, but yes, you should be able to adjust it behind the >> drip tray. They are frequently misaligned; you may have to pull the cover >> once to move it into place. >> b >> >> Sent from my 8-track deck >> >> On Mar 4, 2012, at 5:21, Japheth Lim <[email protected]> wrote: >> >> >> >> >> >> >> >>> Is the OPV supposed to be accessible from behind the drip tray >>> (without having to open it up)? Mine seem to be misaligned. here's a >>> photo of >>> ithttps://plus.google.com/u/0/photos/105771079439875401276/albums/57160... >> >>> On Mar 2, 11:03 am, Ben McCafferty <[email protected]> wrote: >>>> I'd set it to 9 with the blind PF, which give you around. 8.5 when >>>> extracting. >>>> 11 is too high. >>>> b >> >>>> Sent from my 8-track deck >> >>>> On Mar 1, 2012, at 18:03, Japheth Lim <[email protected]> wrote: >> >>>>> Hi all, I am a relatively new user of a Brewtus III-V, and I am >>>>> wondering if I should calibrate the brew pressure down from 11 bars to >>>>> 10. I remember reading that the OPV is supposed to regulate pressure >>>>> by bleeding off excess pressure, thereby maintaining brew pressure at >>>>> 9 bars. Is that right? >> >>>>> -- >>>>> You received this message because you are subscribed to the Google Groups >>>>> "Brewtus" group. >>>>> To post to this group, send email to [email protected]. >>>>> To unsubscribe from this group, send email to >>>>> [email protected]. >>>>> For more options, visit this group >>>>> athttp://groups.google.com/group/brewtus?hl=en. >> >>> -- >>> You received this message because you are subscribed to the Google Groups >>> "Brewtus" group. >>> To post to this group, send email to [email protected]. >>> To unsubscribe from this group, send email to >>> [email protected]. >>> For more options, visit this group >>> athttp://groups.google.com/group/brewtus?hl=en. > > -- > You received this message because you are subscribed to the Google Groups > "Brewtus" group. > To post to this group, send email to [email protected]. > To unsubscribe from this group, send email to > [email protected]. > For more options, visit this group at > http://groups.google.com/group/brewtus?hl=en. > -- You received this message because you are subscribed to the Google Groups "Brewtus" group. To post to this group, send email to [email protected]. To unsubscribe from this group, send email to [email protected]. For more options, visit this group at http://groups.google.com/group/brewtus?hl=en.
