Post to [email protected] for general response.
Gary
Sent with AquaMail for Android
http://www.aqua-mail.com
On May 2, 2017 8:13:59 PM Frederic R Wenzel via BVARC <[email protected]> wrote:
Glad to offer possible assistance. Good luck on your project.
Do you know how I can post a question to the entire BVARC community?
I have an interesting question regarding EMP I am sure will get lots of
responses.
On May 1, 2017, at 7:52 PM, Gary Sitton via BVARC <[email protected]> wrote:
Fred:
I believe I found a local solution, but thanks. I'll
keep you in mind if this doesn't work out.
73s,
Gary Sitton, K5AMH
[email protected] <mailto:[email protected]>
On 5/1/2017 19:12, Frederic R Wenzel via BVARC wrote:
We have machining equipment that can machine your holes for you. I assume
from note below, that you just need to enlarge the 0.500” holes to 0.750”
holes (though holes). This is easy job to accomplish.
We are in Katy at 27027 Westheimer Parkway, suite 700, Katy, TX 77494.
Just south of Katy Mills Mall. Give us a call at 281-382-8987, or my cell
at 713-206-7802 tomorrow to discuss.
On May 1, 2017, at 6:57 PM, Rick Hiller via BVARC <[email protected]
<mailto:[email protected]>> wrote:
Ok I'm an idiot. You want to enlarge the holes. Sorry. Misunderstood.
Never mind my offer. Again sorry!
Sent from my i-Thingamajig
On May 1, 2017, at 6:16 PM, rodney martinez via BVARC <[email protected]
<mailto:[email protected]>> wrote:
My bad....center punching is not necessary with a HALF INCH existing hole.
Didnt read the minor details in the request. Anyway, call me and we can do
it here. I have a 24 volt monster drill here. You hold one side, and I
will hold the other.
Rod
On Monday, May 1, 2017 6:08 PM, rodney martinez via BVARC <[email protected]
<mailto:[email protected]>> wrote:
I have a heavy duty portable drill, and center punching. We can do it here
in my garage in Meyerland.
Helping out a fellow BVARC member tomorrow morning at 1100, but home after
1300 hours tomorrow afternoon.
Rod Martinez
KC5MZK
832-423-5640
On Monday, May 1, 2017 5:54 PM, Gary Sitton via BVARC <[email protected]
<mailto:[email protected]>> wrote:
Anyone know of anyone with the skills and tools to bore out four 1/2" holes
in an aluminum plate to 3/4". I'm very willing to pay. I considered a
step-bit or a straight drill but either is tricky, etc. This is for a base
plate on an antenna mast. The material is 6061-T6.
Gary, K5AMH
Sent with AquaMail for Android
http://www.aqua-mail.com <http://www.aqua-mail.com/>
_______________________________________________
BVARC mailing list
[email protected] <mailto:[email protected]>
http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org
<http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org>
Message delivered to [email protected] <mailto:[email protected]>
_______________________________________________
BVARC mailing list
[email protected] <mailto:[email protected]>
http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org
<http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org>
Message delivered to [email protected] <mailto:[email protected]>
_______________________________________________
BVARC mailing list
[email protected] <mailto:[email protected]>
http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org
<http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org>
Message delivered to [email protected] <mailto:[email protected]>
_______________________________________________
BVARC mailing list
[email protected] <mailto:[email protected]>
http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org
<http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org>
Message delivered to [email protected] <mailto:[email protected]>
_______________________________________________
BVARC mailing list
[email protected] <mailto:[email protected]>
http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org
<http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org>
Message delivered to [email protected] <mailto:[email protected]>
_______________________________________________
BVARC mailing list
[email protected]
http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org
Message delivered to [email protected]
----------
_______________________________________________
BVARC mailing list
[email protected]
http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org
Message delivered to [email protected]
_______________________________________________
BVARC mailing list
[email protected]
http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org
Message delivered to [email protected]
