Here is my HT502 configuration screen. I need a second eye to see if anything is misconfigured. http://www.timepassindia.com/ht502.zip Thanks! Frank
On Jan 28, 2008 11:39 AM, Frank Liu <[EMAIL PROTECTED]> wrote: > So far I still have no luck. > Any more suggestions? > I disabled the iptables fw on the server side, so it's wide open. > client side, ht502 is behind a Buffalo/dd-wrt home router. Do I use > special firewall rules on the client side? voice calls are fine with > 2 way voice, and I don't need to do anything on the home router. > > Frank > > > On Jan 21, 2008 12:56 AM, Damjan Jovanovic <[EMAIL PROTECTED]> wrote: > > > > Same thing happens with both versions of spandsp: the call starts, the > > T.38 session is successfully established, and then Callweaver correctly > > sends CED, v21-preamble, CSI, DIS, no-signal. The other side however > > just sends CNG, and eventually times out and sends a DCN. > > > > You're going through a NAT. Does the other side actually get any > > RTP/T.38 traffic coming from Callweaver? If you make a normal call, do > > you get two-way voice? > > > > Also you're setting various fax-related variables (LOCALSTATIONID, > > LOCALHEADERINFO). Try without them. > > > > Finally, try to Answer() the call, Wait(4) seconds or so, then RxFAX(). > > Maybe the other side doesn't like us starting too early? > > > > Damjan > > > > > > On Mon, 2008-01-21 at 00:42 -0800, Frank Liu wrote: > > > Just tried the latest spandsp snapshot and recompiled the callweaver. > > > Same error on the CLI screen. New "full" log and tcpdump can be found at > > > http://timepassindia.com/faxtroublenew.zip > > > Again, to view tcpdump capture, make sure to decode port 8000 as SIP. > > > > > > Thanks! > > > Frank > > > > > > On Jan 20, 2008 9:32 PM, Damjan Jovanovic <[EMAIL PROTECTED]> wrote: > > > > Use the latest snapshot of spandsp from > > > > http://www.soft-switch.org/downloads/snapshots/spandsp/, it is currently > > > > version 20080110. A number of bugs have been fixed since the version > > > > you're using, 0.0.4pre16. Remember to recompile callweaver after > > > > changing spandsp. > > > > > > > > Start the tcpdump before the fax starts and stop it after the call is > > > > over. The one you sent is useless, there is no SIP in it at all. > > > > > > > > > > > > On Sun, 2008-01-20 at 10:54 -0800, Frank Liu wrote: > > > > > Here it is > > > > > http://timepassindia.com/t38troubleshoot.zip > > > > > > > > > > On Jan 20, 2008 10:32 AM, CtRiX <[EMAIL PROTECTED]> wrote: > > > > > > Frank Liu wrote: > > > > > > > fax is failed. > > > > > > > btw, I have spandsp-0.0.4-0.8.pre16 > > > > > > > > > > > > > > > > > > > > See Trobleshooting at > > > > > > http://www.callweaver.org/wiki/Faxing+With+CallWeaver > > > > > > > > > > > > Max > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > _______________________________________________ > > > > > > Callweaver-dev mailing list > > > > > > [email protected] > > > > > > http://lists.callweaver.org/mailman/listinfo/callweaver-dev > > > > > > > > > > > _______________________________________________ > > > > > Callweaver-dev mailing list > > > > > [email protected] > > > > > http://lists.callweaver.org/mailman/listinfo/callweaver-dev > > > > > > > > Damjan > > > > > > > > > > > > > > > > _______________________________________________ > > > > Callweaver-dev mailing list > > > > [email protected] > > > > http://lists.callweaver.org/mailman/listinfo/callweaver-dev > > > > > > > _______________________________________________ > > > Callweaver-dev mailing list > > > [email protected] > > > http://lists.callweaver.org/mailman/listinfo/callweaver-dev > > > > _______________________________________________ > > Callweaver-dev mailing list > > [email protected] > > http://lists.callweaver.org/mailman/listinfo/callweaver-dev > > > _______________________________________________ Callweaver-dev mailing list [email protected] http://lists.callweaver.org/mailman/listinfo/callweaver-dev
