Thanks, Matt
At 07:02 PM 3/6/2003 -0600, you wrote:
Matt,
The Sanderson is a very nice quality header. But, like I said, I had to dimple a tube on each side. Very disappointing ! However, I did talk with another guy that has a set on his '69 Chevelle w/427, and did not have any fitment problems. If you have not already done so, check out www.sandersonheaders.com . Do not use their measurements that are listed on the website (are not accurate). I have a Moroso oil pan which has the "kickouts" on bottom of each side of the pan. After talking with the Sanderson people on the phone, they told me that their "full length" header would NOT fit with the oil pan I am using. Then I ran across an article in Chevy High Performance (I believe..) where the owner stated he was running a set of the Sanderson "full length" headers on his '69 Chevelle w/427. Called information, got his number, and talked with the guy. He was very helpful, even took time out to take some measurements for me. Needless to say, I purchased a set from Sanderson. They clear the oil pan with plenty of room to spare. The only problem being the oil filter is a tight fit with the oil pan "kickouts". Need to turn the filter sideways to install/remove. Could be messy. Also, they (Sanderson) do not recommend the use of header gaskets to seal the header to the head. Instead they say to use only black silicone or black rtv (cannot remember which ?). You can read about it on the web site. I applied the product that they recommended, but have not run the engine yet to see how it works. But check out the website, because they also have a "shorty" set of headers that would allow even more ground clearance. They also offer a different header flange for those who have a GEN VI engine, which allows for the extra room required to clear the head bolts w/thick washers.
Good Luck,
Kent '68 Malibu ZZ502/502 :) ACES #5102
----- Original Message ----- From: "Matthew Post" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Thursday, March 06, 2003 12:18 PM Subject: Re: [Chevelle-List] Header Question
> thanks Kent! the set that I have currently (unknown brand) have developed > a leak. replaced the gaskets at the head but they're still leaking on the > driver's side. I think they may have rusted out or cracked. (they're very > old.) one way to find out is to probably pull the driver's side off and > check it out. but I've been thinking about replacing them. Sanderson's > are expensive, but if the quality and fit are good, they might be worth it. > > Matt > '69 Malibu 396/th400 > soon to be 4 or 5 speed! > > At 07:55 PM 3/5/2003 -0600, you wrote: > >Have a set of the Sanderson "full length" 1 7/8" on my BB 502. Had to > >dimple a tube on each side for clearance, :( but the quality is very nice, > >and the ground clearance is good too. > > > >Kent > >'68 Malibu ZZ502/502 > >ACES #5102 > > > >----- Original Message ----- > >From: "Clint Hooper" <[EMAIL PROTECTED]> > >To: <[EMAIL PROTECTED]> > >Sent: Tuesday, March 04, 2003 9:05 PM > >Subject: Re: [Chevelle-List] Header Question > > > > > > > I had some 1 7/8" Sanderson intermediates on my former 68 Elky BB car. Not > > > cheap but great quality. Super ground clearance,too. > > > Clint Hooper > > > LT5 Registry Director > > > '91 ZR-1 Callaway Aerobody > > > http://www.LT5Registry.net/ > > > '69 El Camino ProTourer ACES #1650 > > > http://dalesplace.com/misc/friends/clint_hooper.htm > > > '99 Honda F6 Valkyrie custom for sale > > > ----- Original Message ----- > > > From: William King <[EMAIL PROTECTED]> > > > > > > > One word when it comes to headers..Dont. Look into Sanderson Exhaust > > > > manifolds. Hi flow, bolt on, never tighten. > > > > > > > > > > > > ----------------------------------------------------- > > > To Unsubscribe please visit www.chevelles.net/list.html > > > To start a new topic, send mail to: [EMAIL PROTECTED] > > > > > >----------------------------------------------------- > >To Unsubscribe please visit www.chevelles.net/list.html > >To start a new topic, send mail to: [EMAIL PROTECTED] > > > > ----------------------------------------------------- > To Unsubscribe please visit www.chevelles.net/list.html > To start a new topic, send mail to: [EMAIL PROTECTED] >
----------------------------------------------------- To Unsubscribe please visit www.chevelles.net/list.html To start a new topic, send mail to: [EMAIL PROTECTED]
----------------------------------------------------- To Unsubscribe please visit www.chevelles.net/list.html To start a new topic, send mail to: [EMAIL PROTECTED]
