Hi, After load IP Base image (aprox 26MB), I formated the flash, and re-tried the load, and fail again!!!
Router#sh flash: No files on device 63983616 bytes available (0 bytes used) Router# Loading c2800nm-advipservicesk9-mz.124-15.T1.bin from 66.86.36.233 (via GigabitEthernet0/0): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! %Error writing flash:/c2800nm-advipservicesk9-mz.124-15.T1.bin (No space left on device) Sincerely, I'm so tired... and I need the load that image into the router... and I don't have one manner for that... pls... sugestions... Rgds. On 10/19/07, Jonathan Charles <[EMAIL PROTECTED]> wrote: > > Well, from rommon, there isn't much you can do... > > The goal was to format the flash, and then tftp (in IOS, after it > loaded)... > > The timeouts could be a network issue... or you are using an older > tftp server that doesn't support files larger than 18.4mb. > > > > Jonathan > > On 10/19/07, omar parihuana <[EMAIL PROTECTED]> wrote: > > Hi all, > > > > I erased the flash and rebooted the router after reset I tried load the > IOS > > in rommon mode, unfortunately the load didn't complete, I tried again > and > > failed again, I thought tftp failure because I get TFTP timeout: > > > > > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!..!!!!.!!!!.!!!!.!!!.!.!!.!..!.!!.!!.!..!!.................. > > [TIMED OUT] > > TFTP: Operation terminated. > > > > After that I think that my flash memory is incorrect, how can I know if > my > > flash is working well, or maybe is not working anymore!? > > > > Thanks for your response... > > > > PD. At this moment, my router is in rommon mode, and I don't know > > troubleshooting my flash... > > > > > > > > > > On 10/18/07, Jonathan Charles <[EMAIL PROTECTED]> wrote: > > > > > > Well, build a tarball of your IOS and CME files and just archive tar > > > /extract it to the flash > > > > > > > > > > > > Jonathan > > > > > > On 10/18/07, Adrian Chadd <[EMAIL PROTECTED]> wrote: > > > > On Thu, Oct 18, 2007, Jonathan Charles wrote: > > > > > Issue a format flash: > > > > > > > > > > It takes about 2 seconds and wipes it clean... > > > > > > > > > > Besides, no one uses SDM anyway... > > > > > > > > "oh crap all of my CME files are gone!" > > > > > > > > Its generally fine to start with, but then strange crap happens. > Phones > > > > don't ring right, new phones don't get updated firmware, ATAs stop > > working, > > > > etc. Then you swear. Loudly. :) > > > > > > > > (And squeeze flash isn't supported everywhere iirc.) > > > > > > > > > > > > > > > > Adrian > > > > > > > > > > > _______________________________________________ > > > cisco-nsp mailing list [email protected] > > > https://puck.nether.net/mailman/listinfo/cisco-nsp > > > archive at http://puck.nether.net/pipermail/cisco-nsp/ > > > > > > > > > > > -- > > Omar E.P.T > > ----------------- > > Certified Networking Professionals make better Connections! > > > > > -- Omar E.P.T ----------------- Certified Networking Professionals make better Connections! _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
