Hi, Sounds weird.
You're right. It seems a problem with csc0. I guess it's only 4 because there's only one CSC active at any time. -----Mensagem original----- De: Antonio Soares [mailto:[email protected]] Enviada em: segunda-feira, 16 de novembro de 2009 10:49 Para: Leonardo Gama Souza; [email protected] Assunto: RE: [c-nsp] FABRIC-3-ERR_HANDLE No problems with that output: 12k2>show control errors fabric SCA192 SCA192 SCA192 SCA192 XBAR192 XBAR192 CSCFPGA CSCFPGA CLKFPGA LC_ENA BP_FRC LC_TYP DE_GNT DAT_LOS SEL_IDL LP_BAK LC_PRE CLKSTS SLOT0 OK OK OK OK OK OK OK OK OK SLOT1 OK OK OK OK OK OK OK OK OK SLOT2 OK OK OK OK OK OK OK OK OK SLOT3 OK OK OK OK OK OK OK OK OK SLOT4 OK OK OK OK OK OK OK OK OK SLOT5 OK OK OK OK OK OK OK OK OK SLOT6 OK OK OK OK OK OK OK OK OK SLOT7 OK OK OK OK OK OK OK OK OK SLOT8 OK OK OK OK OK OK OK OK OK SLOT9 OK OK OK OK OK OK OK OK OK SLOT10 OK OK OK OK OK OK OK OK OK SLOT11 OK OK OK OK OK OK OK OK OK SLOT12 OK OK OK OK OK OK OK OK OK SLOT13 OK OK OK OK OK OK OK OK OK SLOT14 OK OK OK OK OK OK OK OK OK SLOT15 OK OK OK OK OK OK OK OK OK Fabric error handling : enabled 12k2> But i get the same type of pattern when doing the "execute-on slot x show controllers fia" for other SIP601 slots. And the pattern is: Switch cards present: 0x1F Switch cards monitored: 0x1F 0 1 2 3 4 -------- -------- -------- -------- -------- los 0 0 0 0 0 state Off Off Off Off Off crc16 XXXXX 0 0 0 0 xor error0 0 0 0 cell dropsYYYY YYYY YYYY YYYY XXXX and YYYY have non-zero values. Here the column '0' must be csc0. So the problem must be with csc0. I don't understand why in the line 'cell drops' i only have 4 values. I was expecting 5 as with the other lines. Regards, Antonio Soares, CCIE #18473 (R&S) [email protected] -----Original Message----- From: Leonardo Gama Souza [mailto:[email protected]] Sent: segunda-feira, 16 de Novembro de 2009 12:41 To: Antonio Soares; [email protected] Subject: RES: [c-nsp] FABRIC-3-ERR_HANDLE Hi, What is the output from 'show controllers errors fabric'? First of all I would try to reseat the LC6 and see if the CRC errors stop. -----Mensagem original----- De: [email protected] [mailto:[email protected]] Em nome de Antonio Soares Enviada em: segunda-feira, 16 de novembro de 2009 10:15 Para: [email protected] Assunto: [c-nsp] FABRIC-3-ERR_HANDLE Hello group, I have a 12k reporting this: %FABRIC-3-ERR_HANDLE: Reconfigure LC on fabric due to CRC error from slot 6 In one week, i have 4 of these messages. Slot 6 is a SIP-601 containing 2 x SPA-10G. What could be the problem ? The "show controllers fia" do not show any problem. The "execute-on slot 6 show controllers fia" show this: Switch cards present: 0x1F Switch cards monitored: 0x1F 0 1 2 3 4 -------- -------- -------- -------- -------- los 0 0 0 0 0 state Off Off Off Off Off crc16 53989 0 0 0 0 xor error0 0 0 0 cell drops1020 1020 1020 1020 IOS=c12kprp-p-mz.120-32.SY6.bin Thanks. Regards, Antonio Soares, CCIE #18473 (R&S) [email protected] _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/ _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
