Thanks for the feedback! Sent from my iPhone
> On Apr 19, 2016, at 11:42 PM, Andrew Thrift <[email protected]> wrote: > > Just an update on this old thread, I got slightly side-tracked.. > > Wes's solution does indeed work (Thanks Wes) > > We have it in production with a few hundred peers now. > >> On Tue, Dec 8, 2015 at 5:00 PM, Wes Smith <[email protected]> wrote: >> Hmm >> I grabbed that config from a working asr1002x on 3.16. >> I've been using that for a while with dynamic neighbors in a vrf. >> >> range config is in the root bgp config and the peer-group is defined in the >> address family for the vrf. >> >> >> >> Sent from my iPhone >> >>> On Dec 7, 2015, at 10:06 PM, Andrew Thrift <[email protected]> wrote: >>> >>> Thanks Wes. >>> >>> I did try what you have suggested, and it works if you specify a >>> neighbour/peer-group binding, but you do not seem to be able to >>> specify a "bgp listen range" so it does not accept dynamic neighbours. >>> :( >>> >>> >>> >>> >>>> On Tue, Dec 8, 2015 at 3:29 PM, Wes Smith <[email protected]> wrote: >>>> Hi Andrew >>>> For dynamic peers on a vrf, .... You put the peer group within >>>> 'address-family ipv4 vrf xyz' paragraph like this .. >>>> You end up creating a separate peer-group per vrf >>>> >>>> router bgp 1234 >>>> bgp listen range 10.xx1.0/24 peer-group DYNPEER >>>> bgp listen limit 1000 >>>> >>>> address-family ipv4 vrf XYZ >>>> neighbor DYNPEER peer-group >>>> neighbor DYNPEER remote-as 65011 >>>> neighbor DYNPEER timers 10 65 >>>> neighbor DYNPEER etc etc >>>> ,,,,, >>>> Wes >>>> >>>>> Date: Tue, 8 Dec 2015 14:44:54 +1300 >>>>> From: [email protected] >>>>> To: [email protected] >>>>> Subject: [c-nsp] BGP Dynamic Neighbors + VRF >>>> >>>>> >>>>> Hello, >>>>> >>>>> I have been trying to set up BGP Dynamic Neighbors on a Cisco ASR1002 >>>>> as per the documentation >>>>> >>>>> "http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_bgp/configuration/15-mt/irg-15-mt-book/bgp_dynamic_neighbors.pdf"; >>>>> but am coming unstuck when trying to bind to the peer-group from >>>>> within a VRF. >>>>> >>>>> Basic config is: >>>>> >>>>> router bgp 65000 >>>>> remote-as 65000 >>>>> >>>>> bgp log-neighbor-changes >>>>> bgp listen range 10.23.3.0/24 peer-group nz-peers >>>>> bgp listen limit 200 >>>>> neighbor nz-peers peer-group >>>>> neighbor nz-peers remote-as 64632 >>>>> neighbor nz-peers ebgp-multihop 255 >>>>> >>>>> address-family ipv4 vrf vrf-nz-wan >>>>> redistribute connected >>>>> neighbor nz-peers activate >>>>> exit-address-family >>>>> >>>>> >>>>> However when issuing "neighbor nz-peers activate" I get the following >>>>> error: >>>>> >>>>> % Specify remote-as or peer-group commands first >>>>> >>>>> Is this a configuration that others have done ? Or am I missing >>>>> something fundamental ? >>>>> >>>>> >>>>> Regards, >>>>> >>>>> >>>>> >>>>> Andrew >>>>> _______________________________________________ >>>>> cisco-nsp mailing list [email protected] >>>>> https://puck.nether.net/mailman/listinfo/cisco-nsp >>>>> archive at http://puck.nether.net/pipermail/cisco-nsp/ _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
