Looks good to me. Might want to pull the CallManager traces to see if the call comes in after going off-hook okay. I can look at them if you want to throw them up on dropbox or something. Sounds like it's doing something now at least.
On Fri, Mar 13, 2015 at 5:15 PM, Barry Howser <[email protected]> wrote: > Brian, > > I have attached the screen shot of the sip dial rule. > > I have the ATA187 using the same CSS on the device and line. That CSS only > accesses one partition. That partition has one translation pattern, with a > "blank" pattern field and the digits 9911 in the "Called Party > Transformation" field. The translation pattern uses a CSS that has access > to a 9.911 route pattern (pattern discards predot). > > thanks > > On Fri, Mar 13, 2015 at 4:58 PM, Brian Meade <[email protected]> wrote: > >> Sorry, it was the ATA187s I tried this on. Can you attach a screenshot >> of your dial rule config? >> >> On Fri, Mar 13, 2015 at 4:15 PM, Brian Meade <[email protected]> wrote: >> >>> Right, that's correct. Add 2 PLARs to the SIP Dial Rule with >>> descriptions both with just a button parameter. >>> >>> I've used this for ATA 188s but haven't tested specifically on the 190. >>> >>> On Fri, Mar 13, 2015 at 3:46 PM, Barry Howser <[email protected]> >>> wrote: >>> >>>> hi Brian, >>>> >>>> So what you're saying is that in the SIP dial rule; I'll click the "Add >>>> Plar" button and then give my parameter a description, select "Button" as >>>> my dial parameter then in the value box I'd enter a "1" or a "2" depending >>>> on if I wanted the *PLAR* working on line 1 or 2 of the ATA. >>>> >>>> I would then assume that if I wanted both ATA lines to plar, I would >>>> have two parameters in the SIP dial rule? >>>> >>>> Oyyyy ..... I wish you would write Cisco docs .... I can understand >>>> you, lol. >>>> >>>> >>>> On Fri, Mar 13, 2015 at 3:38 PM, Brian Meade <[email protected]> wrote: >>>> >>>>> For the SIP Dial Rule, all you want it to have is a PLAR with Button 1 >>>>> set. Don't enter the number you want to PLAR to. Then just set up PLAR >>>>> like you would for a SCCP phone with a new CSS/partition/blank translation >>>>> pattern. >>>>> >>>>> On Fri, Mar 13, 2015 at 3:30 PM, Barry Howser <[email protected]> >>>>> wrote: >>>>> >>>>>> Hello everyone. >>>>>> >>>>>> I have an ATA190 that needs to do a plar to 911. My dial plan uses >>>>>> "9" to access an outside line (including the 911 pattern). >>>>>> >>>>>> I created a SIP dial rule and added a plar pattern. I added a >>>>>> parameter called "911" in the description and then added 9911 in the >>>>>> value >>>>>> field. I saved, applied config and restarted. >>>>>> >>>>>> I have applied that SIP Dial Rule to the ATA190 device's sip dial >>>>>> rule section and reset the ATA. When I take either of the lines off hook >>>>>> with an analog phone, I just get dial tone .... no PLARing. >>>>>> >>>>>> What am I doing wrong? >>>>>> >>>>>> thanks >>>>>> >>>>>> _______________________________________________ >>>>>> cisco-voip mailing list >>>>>> [email protected] >>>>>> https://puck.nether.net/mailman/listinfo/cisco-voip >>>>>> >>>>>> >>>>> >>>> >>> >> >
_______________________________________________ cisco-voip mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-voip
