That looks like it John. Strange how it only happens with these serial
interfaces on this 3640 and not on the whole lot of them running the same
IOS. Some things in life just can't be explained. Thx for the help.
--
James Haynes
Network Architect
Cendant IT
A+,MCSE,CCNA,CCDA,CCNP,CCDP
""John Neiberger"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> This might be the problem (from CCO):
>
>
>
> Bug Id : CSCdj83780
> Headline no clockrate is broken on serial wic interfaces
> Product c3600 Model
> Component c3600 Duplicate of
> Severity 2 Status R
> Version Found 11.3(2)T 11.3(1.6)T 11.3Q
> Fixed-in Version 11.3(2)XA 11.3(2.1) 11.3(2.1)T 11.3(2.1)CI
> 11.2(12.1)P 11.3(2.1)Q
> Release Notes
>
> The ''no clockrate'' command is broken on serial wic interfaces of the
> 3600.
> For 3600 images, the clock rate on the serial WIC cannot be removed.
> However, it is possible to change the clock rate on this interface by
> issuing
> the command ''clock rate xxxx'', where xxxx is the desired clock rate
> for the interface.
> This defect affects only the serial WIC interfaces of the 3600.
> All other serial interfaces on the 3600 are unaffected.
>
>
>
> HTH,
> John
>
> >>> "Circusnuts" 4/25/01 10:47:05 AM >>>
> Could be an IOS thing. I've installed a few 3600 & remember taking
> the
> "Enterprise fixes all" approach to loading IOS, only to watch my
> Interfaces
> disappear on the first reload. I had a lot of time to talk with the
> TAC
> about it, as I Kermit-ed some Limited Release IOS (via the console
> cable :o)
> I would say short of trying a reload & applying No IP Address (which I
> think
> you've done), I'd just type a real obvious Description (something
> like:
> Interface Not In Service or Future Use).
>
> Sorry- nothing left in my bag of tricks :o)
> Phil
>
> ----- Original Message -----
> From: James Haynes
> To:
> Sent: Wednesday, April 25, 2001 12:06 PM
> Subject: Re: %Clock rate is ignored on DTE interfaces. [7:1875]
>
>
> > Phil,
> >
> > Thx for the suggestions. I am cleaning up. I was handed this network
> with
> > very out of date documentation and no explanation of why certain
> things
> were
> > configured certain ways. It's like slogging thru the mud trying to
> figure
> > some of this out, but I look at it as a learning opportunity. I've
> tried
> the
> > commands after a no shutdown of the interfaces and have used the
> version
> of
> > the command with the space in it and the exact bandwidth as well.
> The
> > interface still tells me it's setting the clockrate to the default
> value
> > 2015232.
> >
> > --
> > James Haynes
> > Network Architect
> > Cendant IT
> > A+,MCSE,CCNA,CCDA,CCNP,CCDP
> >
> >
> > ""Circusnuts"" wrote in message
> > [EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> > > First- if the interface is in shutdown mode, nothing configured
> takes
> > > effect. I'm guessing you're cleaning things up for who may come
> behind
> > you,
> > > wondering why this configured interface is down :o) Complete the
> command
> > to
> > > represent "no clockrate 2015232." Keep in mind too- starting
> somewhere
> > > around 11.X, the command changed to Clock Rate. I use Clockrate
> (no
> > space)
> > > out of habit & find the command gets kicked back every so often.
> > >
> > > Let us know how you make out
> > > Phil
> > >
> > >
> > > ----- Original Message -----
> > > From: James Haynes
> > > To:
> > > Sent: Wednesday, April 25, 2001 11:08 AM
> > > Subject: %Clock rate is ignored on DTE interfaces. [7:1875]
> > >
> > >
> > > > I have a remote 3640 running IOS (tm) 3600 Software
> (C3640-DS-M),
> > Version
> > > > 11.2(12)P, RELEASE SOFTWARE (fc1).
> > > > whenever I look at the config or reload a new config I get the
> > following
> > > > message at the beginning of the config;
> > > >
> > > > %Clock rate is ignored on DTE interfaces.
> > > >
> > > > Looking at the router interfaces I find:
> > > >
> > > > interface Serial3/2
> > > > description Not in Service
> > > > no ip address
> > > > shutdown
> > > > no snmp trap link-status
> > > > clockrate 2015232
> > > > !
> > > > interface Serial3/3
> > > > description Not in Service.
> > > > no ip address
> > > > shutdown
> > > > no snmp trap link-status
> > > > clockrate 2015232
> > > >
> > > > I have issued the command "no clockrate" on each interface only
> to see
> a
> > > > message:
> > > >
> > > > XXXXXXXX(config)#int s3/2
> > > > XXXXXXXX(config-if)#no clockrate
> > > > %Setting clockrate to default value 2015232.
> > > > XXXXXXXX(config)#int s3/3
> > > > XXXXXXXX(config-if)#no clockrate
> > > > %Setting clockrate to default value 2015232.
> > > >
> > > > This is the only 3640 out of many remote sites that is giving me
> this
> > > > message. It also happens to be the only one with any interfaces
> that
> > even
> > > > show a clockrate. I've checked CCO with the message and nothing
> comes
> > back
> > > > that is helpful. Is there a reason for this I am missing, or I
> am
> > missing
> > > > something in the config to stop this. Thx for any help.
> > > >
> > > > --
> > > > James Haynes
> > > > Network Architect
> > > > Cendant IT
> > > > A+,MCSE,CCNA,CCDA,CCNP,CCDP
> > > > FAQ, list archives, and subscription info:
> > > http://www.groupstudy.com/list/cisco.html
> > > > Report misconduct and Nondisclosure violations to
> [EMAIL PROTECTED]
> > > FAQ, list archives, and subscription info:
> > http://www.groupstudy.com/list/cisco.html
> > > Report misconduct and Nondisclosure violations to
> [EMAIL PROTECTED]
> > FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> > Report misconduct and Nondisclosure violations to
> [EMAIL PROTECTED]
> FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
> FAQ, list archives, and subscription info:
http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=1922&t=1875
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
