http://qa.mandrakesoft.com/show_bug.cgi?id=4691
------- Additional Comments From [EMAIL PROTECTED] 2003-12-08 16:54 ------- By the way, version 1.0.4 is out. Best to take last version ? -- Configure bugmail: http://qa.mandrakesoft.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug, or are watching someone who is. ------- Reminder: ------- assigned_to: [EMAIL PROTECTED] status: UNCONFIRMED creation_date: description: I've installed Mandrake 9.2 beta 2 and my sagem fast800 (usb) does not work correctly, here are the remarks I've got : - now it works correctly : I only missed a correct /etc/resolv.conf (either link it to /etc/ppp/resolv.conf or add Free's DNS) - my config has an ethernet card for LAN and Sagem Fast 800 usb for connection to internet via Free - the problem may come from either DrakConnect or script to install eagle driver - I used the assistant - ADSL modem is detected but pppoe is selected instead of pppoa ADSL usb (detected) => it should be selected automatically instead of a LAN connection (what's the point of detecting it otherwise ?) - I did not enter any DNS as I was relying on autodetection - I got a "Bad IP" for eth0 (as in MdK9.1... till I fixed it) - After some reflexion, I modified /etc/sysconfig/network (it had only NETWORKING=yes, I added HOSTNAME and GATEWAYDEV) and then I completed /etc/resolv.conf with DNS to have the ping work (and then internet access) Conclusion : it should work first time, with not so many choices and be foolproof I'll verify again from scratch but I'm waiting till RC1 (or RC2) to verify that it works well. I think it's compulsory for Linux acceptance by the noobie (which I am). Here is an extract of /var/log/messages just after installing which I used for diagnostic (I selected ADI, usb, plug and connection related lines) Aug 11 02:46:10 localhost kernel: ADI: driver V1.0.4_pre5 loaded Aug 11 02:46:10 localhost kernel: usb.c: registered new driver adiusbadsl Aug 11 02:46:10 localhost kernel: ADI: New modem detected, waiting for firmware... Aug 11 02:46:10 localhost kernel: ADI: Binding Hardware to USB 002/002 Aug 11 02:46:10 localhost kernel: ADI: ioctl ADIUSBADSLFIRMWARE received Aug 11 02:46:10 localhost kernel: ADI: Loading firmware to modem... Aug 11 02:46:10 localhost kernel: ADI: Firmware successfully loaded to modem Aug 11 02:46:10 localhost kernel: ADI: ioctl ADIUSBADSLFIRMWARE received Aug 11 02:46:10 localhost kernel: ADI: Loading firmware to modem... Aug 11 02:46:10 localhost kernel: usb-uhci.c: interrupt, status 2, frame# 150 Aug 11 02:46:10 localhost kernel: ADI: EZUSBWrite reset failure with error ffffff92 Aug 11 02:46:10 localhost kernel: ADI: Unable to load firmware to modem! Aug 11 02:46:10 localhost kernel: usb.c: USB disconnect on device 00:11.3-2 address 2 Aug 11 02:46:10 localhost kernel: ADI: Modem removed Aug 11 02:46:10 localhost kernel: 8139too Fast Ethernet driver 0.9.26 Aug 11 02:46:10 localhost kernel: eth0: RealTek RTL8139 Fast Ethernet at 0xd0a2ff00, 00:50:fc:47:c9:d6, IRQ 19 Aug 11 02:46:10 localhost kernel: hub.c: new USB device 00:11.3-2, assigned address 3 Aug 11 02:46:10 localhost kernel: eth0: Setting half-duplex based on auto-negotiated partner ability 0000. Aug 11 02:46:10 localhost kernel: ADI: New USB ADSL device detected, waiting for DSP code... Aug 11 02:46:10 localhost kernel: ADI : created proc entry at : /proc/driver/adimodem/002-003 Aug 11 02:46:00 localhost usb: Initialisation du contr�leur USB (usb-uhci) : succeeded Aug 11 02:46:00 localhost usb: Montage du syst�me de fichier USB succeeded Aug 11 02:46:04 localhost /etc/hotplug/usb.agent: Setup adiusbadsl for USB product 1110/9010/4000 Aug 11 02:46:05 localhost /etc/hotplug/usb.agent: ... no modules for USB product 0/0/0 Aug 11 02:46:05 localhost last message repeated 2 times Aug 11 02:46:05 localhost /etc/hotplug/usb.agent: Setup adiusbfirmware adiusbfirmware for USB product 1110/9010/4000 Aug 11 02:46:05 localhost /etc/hotplug/usb.agent: Module setup adiusbfirmware for USB product 1110/9010/4000 Aug 11 02:46:09 localhost network: Application des param�tres r�seau succeeded Aug 11 02:46:09 localhost network: D�marrage de l'interface loopback : succeeded Aug 11 02:46:09 localhost ifplugd(eth0)[986]: Using interface eth0/00:50:FC:47:C9:D6 with driver <8139too> (version: 0.9.26) Aug 11 02:46:09 localhost ifplugd(eth0)[986]: Using detection mode: SIOCETHTOOL Aug 11 02:46:09 localhost ifplugd(eth0)[986]: ifplugd 0.15 successfully initialized, link beat not detected. Aug 11 02:46:09 localhost network: Activation de l'interface eth0 : failed Aug 11 02:46:09 localhost internet: Checking internet connections to start at boot succeeded Aug 11 02:46:10 localhost portmap: D�marrage de portmap succeeded Aug 11 02:46:13 localhost alsa: succeeded Aug 11 02:46:14 localhost /etc/hotplug/usb.agent: Setup adiusbadsl acm for USB product 1110/900f/410b Aug 11 02:46:14 localhost last message repeated 2 times Aug 11 02:46:14 localhost modprobe: modprobe: insmod /lib/modules/2.4.21-6mdk/kernel/drivers/usb/acm.o.gz failed Aug 11 02:46:14 localhost modprobe: modprobe: insmod acm failed Aug 11 02:46:14 localhost /etc/hotplug/usb.agent: ... can't load module acm Aug 11 02:46:14 localhost /etc/hotplug/usb.agent: missing kernel or user mode driver acm Aug 11 02:46:14 localhost /etc/hotplug/usb.agent: Setup adiusbdsp adiusbdsp for USB product 1110/900f/410b Aug 11 02:46:14 localhost /etc/hotplug/usb.agent: Setup adiusbdsp adiusbdsp for USB product 1110/900f/410b Aug 11 02:46:14 localhost /etc/hotplug/usb.agent: Module setup adiusbdsp for USB pr
