http://qa.mandrakesoft.com/show_bug.cgi?id=4691
------- Additional Comments From [EMAIL PROTECTED] 2003-17-09 03:16 -------
The text for configuring ADSL has not changed ("La fa�on la plus courante..."
and ends with "Si vous ne savez pas quoi choisir, utilisez pppoe"). For "Free
non d�group�", that's not appropriate : add "si votre modem a �t� d�tect�,
suivez les choix par d�faut qui devraient vous convenir" (if "Free non d�group�"
and "d�group�" are correctly managed).
Sagem (using pppoa) usb - detected => translate to "Sagem (pppoa utilis�) usb -
d�t�ct�"
previous "Fournisseur d'acc�s" is lost (local instead of freeadsl), that's minor
first DNS is false : 169.254.0.2 (local ?) maybe taken from /etc/resolv/conf
(first one different of 127.0.0.1 ?)
second DNS is ok (next in /etc/resolv.conf)
I chose to erase DNS
next : LAN configuration : ok, no more annoying warning (the example 12.34.56.78
could be changed to something more realistic like 10.0.0.3 ? or 169.254.?.? like
windoze ?)
all previous configuration is kept
enhancements next :
- FQDN is not enforced, could be (would avoid postfix and httpd2 complaints)
- ez-ipupdate could be proposed for non-fix IP ? (later) make a partnership with
dyndns.org !
applying changes, here are all errors produced (after launching drakconnect) :
modprobe: Can't locate module serial
modprobe: Can't locate module serial
Please wait while probing serial ports...
Arr�t de l'interface eth0 : [ OK ]
Arr�t de l'interface eth1 : [ OK ]
Arr�t de l'interface loopback : [ OK ]
Application des param�tres r�seau [ OK ]
D�marrage de l'interface loopback : [ OK ]
Activation de l'interface eth0 : [ OK ]
Activation de l'interface eth1 : [ECHEC ]
Can't get synchro within 60 seconds.
well, failure may be due to Free (I've had this problem before this evening,
problem of synchro), maybe add a link to http://fast800.tuxfamily.org/forums/
for diagnostic ? I had to use my "usual" method of stopadsl;startadsl and
unplug/plug modem to finally get it to work... and martian source is back (see
my bug) with the connection.
May require a more thorough test, what do you think of asking for contribution
on eagle-usb forum ? we may obtain volonteers ? (I can only test Free "non
d�group�", many *lucky* people are "d�group�"). You can open two threads : one
for "d�group�", one for "non d�group�"
/etc/resolv.conf :
search free.fr local
nameserver 127.0.0.1
nameserver 169.254.0.2
nameserver 212.27.39.2 # ppp temp entry
nameserver 212.27.32.177 # ppp temp entry
--
Configure bugmail: http://qa.mandrakesoft.com/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are on the CC list for the bug, or are watching someone who is.
------- Reminder: -------
assigned_to: [EMAIL PROTECTED]
status: NEEDINFO
creation_date:
description:
I've installed Mandrake 9.2 beta 2 and my sagem fast800 (usb) does not work
correctly, here are the remarks I've got :
- now it works correctly : I only missed a correct /etc/resolv.conf (either link
it to /etc/ppp/resolv.conf or add Free's DNS)
- my config has an ethernet card for LAN and Sagem Fast 800 usb for connection
to internet via Free
- the problem may come from either DrakConnect or script to install eagle driver
- I used the assistant
- ADSL modem is detected but pppoe is selected instead of pppoa ADSL usb
(detected) => it should be selected automatically instead of a LAN connection
(what's the point of detecting it otherwise ?)
- I did not enter any DNS as I was relying on autodetection
- I got a "Bad IP" for eth0 (as in MdK9.1... till I fixed it)
- After some reflexion, I modified /etc/sysconfig/network (it had only
NETWORKING=yes, I added HOSTNAME and GATEWAYDEV) and then I completed
/etc/resolv.conf with DNS to have the ping work (and then internet access)
Conclusion : it should work first time, with not so many choices and be foolproof
I'll verify again from scratch but I'm waiting till RC1 (or RC2) to verify that
it works well. I think it's compulsory for Linux acceptance by the noobie (which
I am).
Here is an extract of /var/log/messages just after installing which I used for
diagnostic (I selected ADI, usb, plug and connection related lines)
Aug 11 02:46:10 localhost kernel: ADI: driver V1.0.4_pre5 loaded
Aug 11 02:46:10 localhost kernel: usb.c: registered new driver adiusbadsl
Aug 11 02:46:10 localhost kernel: ADI: New modem detected, waiting for firmware...
Aug 11 02:46:10 localhost kernel: ADI: Binding Hardware to USB 002/002
Aug 11 02:46:10 localhost kernel: ADI: ioctl ADIUSBADSLFIRMWARE received
Aug 11 02:46:10 localhost kernel: ADI: Loading firmware to modem...
Aug 11 02:46:10 localhost kernel: ADI: Firmware successfully loaded to modem
Aug 11 02:46:10 localhost kernel: ADI: ioctl ADIUSBADSLFIRMWARE received
Aug 11 02:46:10 localhost kernel: ADI: Loading firmware to modem...
Aug 11 02:46:10 localhost kernel: usb-uhci.c: interrupt, status 2, frame# 150
Aug 11 02:46:10 localhost kernel: ADI: EZUSBWrite reset failure with error ffffff92
Aug 11 02:46:10 localhost kernel: ADI: Unable to load firmware to modem!
Aug 11 02:46:10 localhost kernel: usb.c: USB disconnect on device 00:11.3-2
address 2
Aug 11 02:46:10 localhost kernel: ADI: Modem removed
Aug 11 02:46:10 localhost kernel: 8139too Fast Ethernet driver 0.9.26
Aug 11 02:46:10 localhost kernel: eth0: RealTek RTL8139 Fast Ethernet at
0xd0a2ff00, 00:50:fc:47:c9:d6, IRQ 19
Aug 11 02:46:10 localhost kernel: hub.c: new USB device 00:11.3-2, assigned
address 3
Aug 11 02:46:10 localhost kernel: eth0: Setting half-duplex based on
auto-negotiated partner ability 0000.
Aug 11 02:46:10 localhost kernel: ADI: New USB ADSL device detected, waiting for
DSP code...
Aug 11 02:46:10 localhost kernel: ADI : created proc entry at :
/proc/driver/adimodem/002-003
Aug 11 02:46:00 localhost usb: Initialisation du contr�leur USB (usb-uhci) :
succeeded
Aug 11 02:46:00 localhost usb: Montage du syst�me de fichier USB succeeded
Aug 11 02:46:04 localhost /etc/hotplug/usb.agent: Setup adiusbadsl for USB
product 1110/9010/4000
Aug 11 02:46:05 localhost /etc/hotplug/usb.agent: ... no modules for USB product
0/0/0
Aug 11 02:46:05 localhost last message repeated 2 times
Aug 11 02:46:05 localhost /etc/hotplug/usb.agent: Setup adiusbfirmware
adiusbfirmware for USB product 1110/9010/4000
Aug 11 02:46:05 localhost /etc/hotplug/usb.agent: Module setup adiusbfirmware
for USB product 1110/9010/4000
Aug 11 02:46:09 localhost network: Application des param�tres r�seau succeeded
Aug 11 02:46:09 localhost network: D�marrage de l'interface loopback : succeeded
Aug 11 02:46:09 localhost ifplugd(eth0)[986]: Using interface
eth0/00:50:FC:47:C9:D6 with driver <8139too> (version: 0.9.26)
Aug 11 02:46:09 localhost ifplugd(eth0)[986]: Using detection mode: SIOCETHTOOL
Aug 11 02:46:09 localhost ifplugd(eth0)[986]: ifplugd 0.15 successfully
initialized, link beat not detected.
Aug 11 02:46:09 localhost network: Activation de l'interface eth0 : failed
Aug 11 02:46:09 localhost internet: Checking internet connections to start at
boot succeeded
Aug 11 02:46:10 localhost portmap: D�marrage de portmap succeeded
Aug 11 02:46:13 localhost alsa: succeeded
Aug 11 02:46:14 localhost /etc/hotplug/usb.agent: Setup adiusbadsl acm for USB
product 1110/900f/410b
Aug 11 02:46:14 localhost last message repeated 2 times
Aug 11 02:46:14 localhost modprobe: modprobe: insmod
/lib/modules/2.4.21-6mdk/kernel/drivers/usb/acm.o.gz failed
Aug 11 02:46:14 localhost modprobe: modprobe: insmod acm failed
Aug 11 02:46:14 localhost /etc/hotplug/usb.agent: ... can't load module acm
Aug 11 02:46:14 localhost /etc/hotplug/usb.agent: missing kernel or user mode
driver acm
Aug 11 02:46:14 localhost /etc/hotplug/usb.agent: Setup adiusbdsp adiusbdsp for
USB product 1110/900f/410b
Aug 11 02:46:14 localhost /etc/hotplug/usb.agent: Setup adiusbdsp adiusbdsp for
USB product 1110/900f/410b
Aug 11 02:46:14 localhost /etc/hotplug/usb.agent: Module setup adiusbdsp for USB pr
