Sorry, I need to read better.

Thank you.

I am going to try the patches now.

Regards,

- Eli


On 24/02/18 00:01, Timothy Pearson wrote:
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

You need these patches:

https://review.coreboot.org/#/c/19822/

This one in particular:

https://review.coreboot.org/#/c/coreboot/+/19820/

This is noted on the Raptor status page:

https://www.raptorengineering.com/coreboot/kgpe-d16-bmc-port-status.php

See the link to "Initial coreboot patches".

If anyone wants to take over upstreaming of the patches in that list
they are welcome to do so!

On 02/23/2018 04:38 PM, Elisenda Cuadros wrote:
Hello,

Thank you for your reply.

I reflashed (same build) the BMC module with a hotplug. Now it works
like a charm, it got an ip, I can log through ssh, reboot, etc..

But now I have a new problem. If I try to boot from a halted system,
with BMC module attached, the system fires up but Coreboot hangs:

Unable to detect valid memory on any nodes.  Halting!
mct_d: fatalexit

If I remove the BMC module the system boots fine.

I have 4 Micron MT18JSF25672PDZ-1G4F1DD modules, located in CPU1 orange
slots.

I attach both console logs.

Regards,

- Eli



On 22/02/18 22:36, Timothy Pearson wrote:
Actually, for OpenBMC work, hotplugging is often the only way to go.
Just be very careful to align the pins correctly the first time; you
don't have a second chance if you misalign the pins and fry the module...

On 02/22/2018 03:22 PM, taii...@gmx.com wrote:
On 02/17/2018 09:46 AM, Elisenda Cuadros wrote:

Hi,

Now I trying to use your OpenBMC port.

I followed the instructions and everything was fine (compiling,
reading and flashing). I waited several minutes after flashing, but
the module didn 't blinked like in the vendor rom, nor did it receive
an ip.

I halted the system because I thought maybe it needs a cold start.

After this, the system doesn't boot with the module plugged in. The
fans begin to spin for approximately 1/4 second, but nothing else.

My two fans (1 cpu & 1 chassis) have 3 pins and are low speed
(~1000rpm)

In the case I have to reflash the module, is it possible to hotplug it?
Hotplugging is dangerous and not supported, don't do it.
Thank you very much for your support.
You can use a test clip to externally flash it via a flashing device
(not sure which can do 16 pins though, I would inquire on the flashrom
mailinglist)

Are you using the latest coreboot? AFAIK coreboot was patched to support
OpenBMC, so you need a new version with the patches.

- -- Timothy Pearson
Raptor Engineering
+1 (415) 727-8645 (direct line)
+1 (512) 690-0200 (switchboard)
https://www.raptorengineering.com
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1

iQEcBAEBAgAGBQJakJ03AAoJEK+E3vEXDOFbW/0H/1DOjUMNrB5tOxw1OkGnRVK0
/KucTV0HjqPwtvhyyHeU6T9cFdAAkTHICFeGXXm05GBSeCTXWKOp38xO92hWCp88
zedukp8mq+AAzg6R1yfd6Z3MsD1pmueUKWvV0ca1lxkfAGacUzND0xRXQaO3Jel6
n0VYv0GOSDCjp34MClawUZ7ie309u68YnEQhkyFd56oXsTCfvHl8j2dwO8RmmtJt
gs+JHOTZAMgBSzn8DJigh5hiNA7B93A8Lst/Q+oFfxwibhSWGDXCmdDlcBu/VNcM
ZNF3DYYa6u6bQB8xNvous8HCn5aUEvU2vNbAci+R15S1fNEnO+fn/+F5X96mHyk=
=DRWR
-----END PGP SIGNATURE-----


--
coreboot mailing list: coreboot@coreboot.org
https://mail.coreboot.org/mailman/listinfo/coreboot

Reply via email to