Sorry guys,
In my haste, I did the ifconfig -a after I had restored the previous good
config - doh!
fxp1 is my dmz which I would like to vlan into different subnets
fxp0 is my wan
fxp2 is my lan
fxp3 is my lan 2
tl0 is for my wlan subnet
tl1 is spare
This is the correct one :
login as: admin
Using keyboard-interactive authentication.
Password:
*** This is pfSense version 0.86 - pfSense ***
LAN -> fxp2 -> 192.168.199.254
WAN -> fxp0 -> dhcp
OPT1 -> fxp3 -> 192.168.200.254(M_server)
OPT2 -> fxp1 -> 172.100.100.254(FE_Server)
OPT3 -> tl0 -> (OPT3)
OPT4 -> tl1 -> (OPT4)
OPT5 -> vlan0 -> (OPT5)
OPT6 -> vlan1 -> (OPT6)
pfSense console setup
***********************
0) Logout (SSH only)
1) Assign Interfaces
2) Set LAN IP address
3) Reset webGUI password
4) Reset to factory defaults
5) Reboot system
6) Halt system
7) Ping host
8) Shell
9) PFtop
10) Traffic Logs
Enter an option: 8
# ifconfig -a
tl0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
ether 00:80:5f:a7:83:4d
media: Ethernet autoselect (none)
status: no carrier
tl1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
ether 00:80:5f:a7:83:cd
media: Ethernet autoselect (none)
status: no carrier
fxp0: flags=9943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,LINK0,MULTICAST> mtu
1500
options=8<VLAN_MTU>
inet6 fe80::250:8bff:fe68:8972%fxp0 prefixlen 64 scopeid 0x3
inet 82.4.0.0 netmask 0xffffff00 broadcast 255.255.255.255
ether 00:50:8b:68:89:72
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
fxp1: flags=9843<UP,BROADCAST,RUNNING,SIMPLEX,LINK0,MULTICAST> mtu 1500
options=8<VLAN_MTU>
inet6 fe80::250:8bff:fe68:8973%fxp1 prefixlen 64 scopeid 0x4
inet 172.100.100.254 netmask 0xffffff00 broadcast 172.100.100.255
ether 00:50:8b:68:89:73
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
fxp2: flags=9843<UP,BROADCAST,RUNNING,SIMPLEX,LINK0,MULTICAST> mtu 1500
options=8<VLAN_MTU>
inet 192.168.199.254 netmask 0xffffff00 broadcast 192.168.199.255
inet6 fe80::208:2ff:fede:cec4%fxp2 prefixlen 64 scopeid 0x5
ether 00:08:02:de:ce:c4
media: Ethernet autoselect (100baseTX)
status: active
fxp3: flags=9843<UP,BROADCAST,RUNNING,SIMPLEX,LINK0,MULTICAST> mtu 1500
options=8<VLAN_MTU>
inet 192.168.200.254 netmask 0xffffff00 broadcast 192.168.200.255
inet6 fe80::208:2ff:fede:cec5%fxp3 prefixlen 64 scopeid 0x6
ether 00:08:02:de:ce:c5
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
plip0: flags=108810<POINTOPOINT,SIMPLEX,MULTICAST,NEEDSGIANT> mtu 1500
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x8
pflog0: flags=141<UP,RUNNING,PROMISC> mtu 33208
pfsync0: flags=41<UP,RUNNING> mtu 2020
pfsync: syncdev: lo0 maxupd: 128
vlan0: flags=8842<BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
ether 00:50:8b:68:89:73
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
vlan: 20 parent interface: fxp1
vlan1: flags=8842<BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
ether 00:50:8b:68:89:73
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
vlan: 30 parent interface: fxp1
#
> --- Ursprüngliche Nachricht ---
> Von: Scott Ullrich <[EMAIL PROTECTED]>
> An: [email protected]
> Betreff: Re: [pfSense-discussion] problem with vlans
> Datum: Wed, 5 Oct 2005 16:51:40 -0400
>
> Yes, please make sure they are assigned correctly. If they are let me
> know and I'll dive into the code.
>
> Scott
>
>
> On 10/5/05, Dan Swartzendruber <[EMAIL PROTECTED]> wrote:
> >
> > if you did create the vlans, you don't seem to have assigned them as
> > interfaces. e.g. when you are in the console menu and see option #1
> > (assign interfaces), you want to assign vlan0 and/or vlan1 as LAN, or
> > OPT or whatever. as is, you have the IP addresses assigned to the
> > real interfaces.
> >
> > At 04:47 PM 10/5/2005, you wrote:
> > ># ifconfig -a
> > >tl0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
> > > ether 00:80:5f:a7:83:4d
> > > media: Ethernet autoselect (none)
> > > status: no carrier
> > >tl1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
> > > ether 00:80:5f:a7:83:cd
> > > media: Ethernet autoselect (none)
> > > status: no carrier
> > >fxp0: flags=9943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,LINK0,MULTICAST>
> mtu
> > >1500
> > > options=8<VLAN_MTU>
> > > inet6 fe80::250:8bff:fe68:8972%fxp0 prefixlen 64 scopeid 0x3
> > > inet 82.4.0.0 netmask 0xffffff00 broadcast 255.255.255.255
> > > ether 00:50:8b:68:89:72
> > > media: Ethernet autoselect (100baseTX <full-duplex>)
> > > status: active
> > >fxp1: flags=9843<UP,BROADCAST,RUNNING,SIMPLEX,LINK0,MULTICAST> mtu 1500
> > > options=8<VLAN_MTU>
> > > inet 172.100.100.254 netmask 0xffffff00 broadcast
> 172.100.100.255
> > > inet6 fe80::250:8bff:fe68:8973%fxp1 prefixlen 64 scopeid 0x4
> > > ether 00:50:8b:68:89:73
> > > media: Ethernet autoselect (100baseTX <full-duplex>)
> > > status: active
> > >fxp2: flags=9843<UP,BROADCAST,RUNNING,SIMPLEX,LINK0,MULTICAST> mtu 1500
> > > options=8<VLAN_MTU>
> > > inet 192.168.199.254 netmask 0xffffff00 broadcast
> 192.168.199.255
> > > inet6 fe80::208:2ff:fede:cec4%fxp2 prefixlen 64 scopeid 0x5
> > > ether 00:08:02:de:ce:c4
> > > media: Ethernet autoselect (100baseTX)
> > > status: active
> > >fxp3: flags=9843<UP,BROADCAST,RUNNING,SIMPLEX,LINK0,MULTICAST> mtu 1500
> > > options=8<VLAN_MTU>
> > > inet 192.168.200.254 netmask 0xffffff00 broadcast
> 192.168.200.255
> > > inet6 fe80::208:2ff:fede:cec5%fxp3 prefixlen 64 scopeid 0x6
> > > ether 00:08:02:de:ce:c5
> > > media: Ethernet autoselect (100baseTX <full-duplex>)
> > > status: active
> > >plip0: flags=108810<POINTOPOINT,SIMPLEX,MULTICAST,NEEDSGIANT> mtu 1500
> > >lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
> > > inet 127.0.0.1 netmask 0xff000000
> > > inet6 ::1 prefixlen 128
> > > inet6 fe80::1%lo0 prefixlen 64 scopeid 0x8
> > >pflog0: flags=141<UP,RUNNING,PROMISC> mtu 33208
> > >pfsync0: flags=41<UP,RUNNING> mtu 2020
> > > pfsync: syncdev: lo0 maxupd: 128
> > >#
> > >
> > >
> > >Hi Dan,
> > >ifconfig -a.
> > >
> > >Any idea what plip0 is ?
> > >
> > >Thanks
> > >
> > >--
> > >GMX DSL = Maximale Leistung zum minimalen Preis!
> > >2000 MB nur 2,99, Flatrate ab 4,99 Euro/Monat:
> http://www.gmx.net/de/go/dsl
> >
> >
> >
>
--
Lust, ein paar Euro nebenbei zu verdienen? Ohne Kosten, ohne Risiko!
Satte Provisionen für GMX Partner: http://www.gmx.net/de/go/partner
