Hi, sad you are not able to reproduce. The good thing i can't reproduce myself either ;-(
it just happens out of nothing on the nodes. My current expection is that it happens when spikes of packets occur after being idle for some time. The good news is after upgrading to the latest intel fw released two days ago and to the latest 1.3.38 driver - it works on 10 out of my 18 testing hosts. Currently i've no idea why it does not on those 8. Stefan Am 19.08.2015 um 00:24 schrieb Rose, Gregory V: > > >> -----Original Message----- >> From: Stefan Priebe - Profihost AG [mailto:s.pri...@profihost.ag] >> Sent: Tuesday, August 18, 2015 12:28 AM >> To: Rose, Gregory V; e1000-devel@lists.sourceforge.net >> Subject: Re: [E1000-devel] dropped rx with i40e >> >> Hi Greg, >> >> could you tell me the output of ethtool -i and ethtool -a and ethtool -c >> and ethtool -k? > > OK, I pasted it in below. I ran traffic overnight and there were no dropped > packets or other errors. Everything seemed fine. > > - Greg > > [root@paelab-gvrose ~]# ethtool -i bond0 > driver: bonding > version: 3.7.1 > firmware-version: 2 > bus-info: > supports-statistics: no > supports-test: no > supports-eeprom-access: no > supports-register-dump: no > supports-priv-flags: no > [root@paelab-gvrose ~]# ethtool -c bond0 > Coalesce parameters for bond0: > Cannot get device coalesce settings: Operation not supported > [root@paelab-gvrose ~]# ethtool -k bond0 > Features for bond0: > rx-checksumming: off [fixed] > tx-checksumming: on > tx-checksum-ipv4: off [fixed] > tx-checksum-ip-generic: on > tx-checksum-ipv6: off [fixed] > tx-checksum-fcoe-crc: off [fixed] > tx-checksum-sctp: off [fixed] > scatter-gather: on > tx-scatter-gather: on > tx-scatter-gather-fraglist: off [requested on] > tcp-segmentation-offload: on > tx-tcp-segmentation: on > tx-tcp-ecn-segmentation: on > tx-tcp6-segmentation: on > udp-fragmentation-offload: off [fixed] > generic-segmentation-offload: on > generic-receive-offload: on > large-receive-offload: off > rx-vlan-offload: on > tx-vlan-offload: on > ntuple-filters: off [fixed] > receive-hashing: off [fixed] > highdma: on > rx-vlan-filter: on > vlan-challenged: off [fixed] > tx-lockless: on [fixed] > netns-local: on [fixed] > tx-gso-robust: off [fixed] > tx-fcoe-segmentation: off [fixed] > tx-gre-segmentation: off [fixed] > tx-ipip-segmentation: off [fixed] > tx-sit-segmentation: off [fixed] > tx-udp_tnl-segmentation: on > tx-mpls-segmentation: off [fixed] > fcoe-mtu: off [fixed] > tx-nocache-copy: off > loopback: off [fixed] > rx-fcs: off [fixed] > rx-all: off [fixed] > tx-vlan-stag-hw-insert: off [fixed] > rx-vlan-stag-hw-parse: off [fixed] > rx-vlan-stag-filter: off [fixed] > l2-fwd-offload: off [fixed] > busy-poll: off [fixed] > [root@paelab-gvrose ~]# ethtool -i p4p1 > driver: i40e > version: 1.2.47 > firmware-version: f4.40.35115 a1.4 n4.53 e1ce7 > bus-info: 0000:82:00.0 > supports-statistics: yes > supports-test: yes > supports-eeprom-access: yes > supports-register-dump: yes > supports-priv-flags: yes > [root@paelab-gvrose ~]# ethtool -c p4p1 > Coalesce parameters for p4p1: > Adaptive RX: on TX: on > stats-block-usecs: 0 > sample-interval: 0 > pkt-rate-low: 0 > pkt-rate-high: 0 > > rx-usecs: 62 > rx-frames: 0 > rx-usecs-irq: 0 > rx-frames-irq: 256 > > tx-usecs: 122 > tx-frames: 0 > tx-usecs-irq: 0 > tx-frames-irq: 256 > > rx-usecs-low: 0 > rx-frame-low: 0 > tx-usecs-low: 0 > tx-frame-low: 0 > > rx-usecs-high: 0 > rx-frame-high: 0 > tx-usecs-high: 0 > tx-frame-high: 0 > > [root@paelab-gvrose ~]# ethtool -k p4p1 > Features for p4p1: > rx-checksumming: on > tx-checksumming: on > tx-checksum-ipv4: on > tx-checksum-ip-generic: off [fixed] > tx-checksum-ipv6: on > tx-checksum-fcoe-crc: off [fixed] > tx-checksum-sctp: on > scatter-gather: on > tx-scatter-gather: on > tx-scatter-gather-fraglist: off [fixed] > tcp-segmentation-offload: on > tx-tcp-segmentation: on > tx-tcp-ecn-segmentation: on > tx-tcp6-segmentation: on > udp-fragmentation-offload: off [fixed] > generic-segmentation-offload: on > generic-receive-offload: on > large-receive-offload: off [fixed] > rx-vlan-offload: on > tx-vlan-offload: on > ntuple-filters: on > receive-hashing: on > highdma: on > rx-vlan-filter: on > vlan-challenged: off [fixed] > tx-lockless: off [fixed] > netns-local: off [fixed] > tx-gso-robust: off [fixed] > tx-fcoe-segmentation: off [fixed] > tx-gre-segmentation: off [fixed] > tx-ipip-segmentation: off [fixed] > tx-sit-segmentation: off [fixed] > tx-udp_tnl-segmentation: on > tx-mpls-segmentation: off [fixed] > fcoe-mtu: off [fixed] > tx-nocache-copy: off > loopback: off [fixed] > rx-fcs: off [fixed] > rx-all: off [fixed] > tx-vlan-stag-hw-insert: off [fixed] > rx-vlan-stag-hw-parse: off [fixed] > rx-vlan-stag-filter: off [fixed] > l2-fwd-offload: off [fixed] > busy-poll: off [fixed] > [root@paelab-gvrose ~]# ethtool -i p4p4 > driver: i40e > version: 1.2.47 > firmware-version: f4.40.35115 a1.4 n4.53 e1ce7 > bus-info: 0000:82:00.3 > supports-statistics: yes > supports-test: yes > supports-eeprom-access: yes > supports-register-dump: yes > supports-priv-flags: yes > [root@paelab-gvrose ~]# ethtool -c p4p4 > Coalesce parameters for p4p4: > Adaptive RX: on TX: on > stats-block-usecs: 0 > sample-interval: 0 > pkt-rate-low: 0 > pkt-rate-high: 0 > > rx-usecs: 62 > rx-frames: 0 > rx-usecs-irq: 0 > rx-frames-irq: 256 > > tx-usecs: 122 > tx-frames: 0 > tx-usecs-irq: 0 > tx-frames-irq: 256 > > rx-usecs-low: 0 > rx-frame-low: 0 > tx-usecs-low: 0 > tx-frame-low: 0 > > rx-usecs-high: 0 > rx-frame-high: 0 > tx-usecs-high: 0 > tx-frame-high: 0 > > [root@paelab-gvrose ~]# ethtool -k p4p4 > Features for p4p4: > rx-checksumming: on > tx-checksumming: on > tx-checksum-ipv4: on > tx-checksum-ip-generic: off [fixed] > tx-checksum-ipv6: on > tx-checksum-fcoe-crc: off [fixed] > tx-checksum-sctp: on > scatter-gather: on > tx-scatter-gather: on > tx-scatter-gather-fraglist: off [fixed] > tcp-segmentation-offload: on > tx-tcp-segmentation: on > tx-tcp-ecn-segmentation: on > tx-tcp6-segmentation: on > udp-fragmentation-offload: off [fixed] > generic-segmentation-offload: on > generic-receive-offload: on > large-receive-offload: off [fixed] > rx-vlan-offload: on > tx-vlan-offload: on > ntuple-filters: on > receive-hashing: on > highdma: on > rx-vlan-filter: on > vlan-challenged: off [fixed] > tx-lockless: off [fixed] > netns-local: off [fixed] > tx-gso-robust: off [fixed] > tx-fcoe-segmentation: off [fixed] > tx-gre-segmentation: off [fixed] > tx-ipip-segmentation: off [fixed] > tx-sit-segmentation: off [fixed] > tx-udp_tnl-segmentation: on > tx-mpls-segmentation: off [fixed] > fcoe-mtu: off [fixed] > tx-nocache-copy: off > loopback: off [fixed] > rx-fcs: off [fixed] > rx-all: off [fixed] > tx-vlan-stag-hw-insert: off [fixed] > rx-vlan-stag-hw-parse: off [fixed] > rx-vlan-stag-filter: off [fixed] > l2-fwd-offload: off [fixed] > busy-poll: off [fixed] > >> >> Another difference to the ixgbe is that >> large-receive-offload is fixed to off in ethtool -k. >> >> Stefan >> Am 17.08.2015 um 23:46 schrieb Rose, Gregory V: >>> >>>>>> -----Original Message----- >>>>>> From: Stefan Priebe [mailto:s.pri...@profihost.ag] >>>>>> Sent: Thursday, August 13, 2015 12:02 PM >>>>>> To: Rose, Gregory V; e1000-devel@lists.sourceforge.net >>>>>> Subject: Re: [E1000-devel] dropped rx with i40e >>>>>> >>>>>> Am 13.08.2015 um 20:59 schrieb Rose, Gregory V: >>>>>>> Thanks Stefan, I'll set up a test to replicate your traffic >>>>>>> profile as >>>>>> closely as possible and let it run overnight to see if I can repro >>>>>> and then update you tomorrow. >>>>>>> >>>>>>> It does seem that it has nothing to do with load so that makes it >>>>>>> even >>>>>> more curious. >>>>>> >>>>>> May it be related to jumbo frames? >>> >>> Stefan, >>> >>> I've got the test up and running now. Here's the interface config: >>> >>> 6: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 9000 qdisc >> noqueue state UP >>> link/ether 68:05:ca:2f:83:10 brd ff:ff:ff:ff:ff:ff >>> inet 200.0.0.10/24 brd 200.0.0.255 scope global bond0 >>> valid_lft forever preferred_lft forever >>> inet6 fe80::6a05:caff:fe2f:8310/64 scope link >>> valid_lft forever preferred_lft forever >>> 9: p4p1: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 9000 qdisc mq >> master bond0 state UP qlen 1000 >>> link/ether 68:05:ca:2f:83:10 brd ff:ff:ff:ff:ff:ff >>> inet6 fe80::6a05:caff:fe2f:8310/64 scope link >>> valid_lft forever preferred_lft forever >>> 12: p4p4: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 9000 qdisc mq >> master bond0 state UP qlen 1000 >>> link/ether 68:05:ca:2f:83:10 brd ff:ff:ff:ff:ff:ff >>> inet6 fe80::6a05:caff:fe2f:8310/64 scope link >>> valid_lft forever preferred_lft forever >>> >>> p4p1 and p4p4 are the i40e interfaces bonded to the bond0 LACP >> interface. >>> >>> Here's the traffic results from a transmitter: >>> >>> Interim result: 9899.84 10^6bits/s over 5.001 seconds ending at >>> 1439847706.406 Interim result: 9900.15 10^6bits/s over 5.001 seconds >>> ending at 1439847711.407 >>> >>> I have a script watching the dropped packets for the two slaved >> interfaces p4p1 and p4p4: >>> >>> Every 1.0s: ./t1 Mon Aug 17 >> 14:43:31 2015 >>> >>> rx_dropped: 0 >>> tx_dropped: 0 >>> rx_fcoe_dropped: 0 >>> port.rx_dropped: 0 >>> port.tx_dropped_link_down: 0 >>> rx_dropped: 0 >>> tx_dropped: 0 >>> rx_fcoe_dropped: 0 >>> port.rx_dropped: 0 >>> port.tx_dropped_link_down: 0 >>> >>> I'll let this run overnight and get back to you with results tomorrow. >>> >>> Regards, >>> >>> - Greg >>> ------------------------------------------------------------------------------ _______________________________________________ E1000-devel mailing list E1000-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/e1000-devel To learn more about Intel® Ethernet, visit http://communities.intel.com/community/wired
