>> I don't have a sub rx, so it's never been a problem for me, but I'm
>> thinking of adding one. How does that work if there's a RTTY
>> signal on both VFO's (simplex)? Would you have to tap A>B?
The best way to handle RTTY with signals on both receivers is to run
two copies of MMTTY (or other decoder) - one for reach receiver. MixW
has a dual receive capability - I don't know about any of the other
software. In general, one decoder uses the soundcard left channel
and the second uses soundcard right channel audio. Mixing the two
audio streams does not work ... it merely results in QRM.
73,
... Joe, W4TV
On 11/27/2010 5:34 AM, Mike wrote:
> Re: point #2.
>
> I don't have a sub rx, so it's never been a problem for me, but I'm thinking
> of
> adding one. How does that work if there's a RTTY signal on both VFO's
> (simplex)?
> Would you have to tap A>B?
>
> The manual sez "Use CONFIG: LIN OUT to set the level, or to switch from a
> fixed-level
> setting to =PHONES." Does that give you a level control using the AF knob?
>
> 73, Mike NF4L
>
> On 11/26/2010 11:52 PM, Richard Ferch wrote:
>> James,
>>
>> I hope your daughter is feeling better soon.
>>
>> Re your questions (based on my observations using sound card software on
>> both channels from the LINE OUT jack, and stereo headphones plugged into
>> the SPKRS jack):
>>
>> 1. The CONFIG:SPKRS setting only affects the rear panel SPKRS jack. It
>> has no effect on LINE OUT.
>>
>> 2. None of the audio mixing or level controls has any effect on the LINE
>> OUT signal, as far as I can tell. The left channel always carries the
>> main RX output, and the right channel always carries the sub RX output.
>> The LINE output is "raw" unmixed audio from the two receivers at a fixed
>> level set by CONFIG:LIN OUT.
>>
>> 3. When CONFIG:SPKRS = 2, the SPKRS jack behaves the same as the
>> headphone jacks. With SUB off, the main RX is in both channels, and with
>> SUB on and the normal L-MIX-R setting, the main RX and sub RX are in
>> left and right channels respectively. Changing the L-MIX-R setting
>> affects the SPKRS the same way as it affects the PHONES output.
>>
>> When CONFIG:SPKRS = 1, the only speaker output is on the left channel of
>> the SPKRS jack, i.e. it disables the right channel output even when SUB
>> is on. If SUB is on, the external mono speaker on the left channel
>> carries audio from both receivers mixed together, the same as the
>> internal speaker. The purpose of the CONFIG:SPKRS = 1 option is to
>> protect the speaker amp if a mono plug is plugged into the SPKRS jack.
>>
>> 73,
>> Rich VE3KI
>>
>>
>>
>>
>>
>>
>> ______________________________________________________________
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft@mailman.qth.net
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>>
>
>
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
