Thanks for your help. See my last post on board. Everything OK now.
brian <mailto:[email protected]>
Thursday, June 4, 2015 5:47 PM
Hi Carl.
I meant which K3 mode have you selected? You should be using digital
mode DATA A. See manual on how to get to this mode.
Use Main Menu "MIC SEL" set to line.
The mic gain control knob on the front panel allows you to set the
audio level the K3 sees with line input.
The rear panel line input plug is a mono plug.
Hope this helps.
Final dumb question. Are you sure there is audio on the input cable
used?
73 and GL
de Brian /K3KO
Carl Jón Denbow <mailto:[email protected]>
Thursday, June 4, 2015 5:33 PM
<<<Which digital mode did you select? >>>
JT9
<<<Are you using mike input or line in input? >>>
Line
<<<If line in, have you adjusted the K3 line in level. >>>
I guess I need instructions about how to do this. Please see earlier
post I made about my inability to find proper menu item.
<<<Make sure you have selected the correct audio input source in the
K3 menu. >>>
Perhaps I need instruction about this too, though I set MIC+LIN to ON.
If using mike input are you using VOX or PTT?
Using PTT via CAT and K3 does key OK, just no audio seems to be TX.
73,
Carl
N8VZ
brian <mailto:[email protected]>
Thursday, June 4, 2015 3:37 PM
Hi Carl,
Which digital mode did you select?
Are you using mike input or line in input?
If line in, have you adjusted the K3 line in level.
Make sure you have selected the correct audio input source in the K3
menu.
If using mike input are you using VOX or PTT?
Is the K3 going into transmit?
73 de Brian/K3KO
Carl Jón Denbow <mailto:[email protected]>
Thursday, June 4, 2015 3:27 PM
I've been trying to set up my data modes using a SignaLink USB, which
I've used with good results with my KX3, with my K3. I do have the
correct K3 jumper board in the SL. I also have the SignaLink supplied
cables hooked up correctly. I can monitor digital signals just fine.
I can not get any TX audio actually transmitted, though Windows
indicates that the USB Codec Speaker is getting plenty of audio on
TX. I've tried to use the Test TX DATA routine within the K3 and get
no ALC even when Windows indicates that that line has full bore
audio. I'm probably doing something rather simple wrong here, but I
can't for the life of me figure out what it might be. In terms of
experience, I'm an old hand at digital modes having run them on
numerous rigs, with various computers and external sound card
combinations over a number of years. I'm, however, very new to the K3
as I just purchased it used at Dayton this year, and I'm just now
trying to hook it up for digital modes. Thanks for any help you can
give. 73 de Carl, N8VZ
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
--
=================================================
Carl Jón Denbow, N8VZ
17 Coventry Lane
Athens, Ohio 45701-3718
[email protected]
www.n8vz.com
EM89wh
IRLP 4533 Echolink 116070
PSK and JT65 Forever!
=================================================
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
