Proberly i should try this one on the hole list as well, sorry don for you
getting it twice.
Hi Don
again thanks
The SSB Firmware was ok, version 1.8 so no problem there.
Now i have found the issue on the K2, but not the solution. The desribed
issue seen on the low power out are comming from the 28-30 Mhz. if i check
indicated power by the internal powermeter it drops over the freq. with the
power set for 5W i do reach 5.4 W on 28 Mhz at 29 Mhz it is 4,9, still ok
but at 30 Mhz it is down at 0,3 W
So trying 10 W 29 Mhz only goes to same 4.9, so a rolloff on increasing
freq. are seen. Proberly normal, but passband seems to be to narrow ???
Any idea is this normal ??
Thanks in advance
Br.
OZ1BZJ
Michael
----- Original Message -----
From: Don Wilhelm
To: [EMAIL PROTECTED]
Cc: Elecraft Support
Sent: Tuesday, February 21, 2006 3:52 PM
Subject: RE: [Elecraft] XV144 calibration
Michael,
If your K2 is SN 5111 and the KSB2 was ordered at the same time as your
K2, then you have the latest KSB2 firmware - Elecraft does not ship any
options with back level firmware.
Yes, if you could achieve only 0.17 mW from the K60XV in TUNE with a 1mV
MENU setting, that is the problem that must be resolved first.
I believe you have something wrong with the K60XV, and I am stumped at the
moment. I do not have the setup to try what you suggested here at this
time, but the behavior you describe is not normal.
Perhaps Gary Surrency can provide some further information and guidance.
I am copying Gary on this email.
73,
Don W3FPR
-----Original Message-----
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]
Sent: Tuesday, February 21, 2006 9:30 AM
To: [EMAIL PROTECTED]; [email protected]; 'Don Wilhelm'
Subject: RE: [Elecraft] XV144 calibration
Thanks Don
Good point, i have proberly been a little careless on this SW
requirement, as i got the K2#5111 with all options in one shipment from
Elecraft. I guess they normal take good care that the right versions are
included when shiping together. But i will indeed check as soon i get home
from work.
If you are the owner of the XV144 and using it in the Low power setup,
could i ask you to use the tune button to TX the transverter with the power
set to the full. and the see if your K2 display will show the 1 mW about.
In my case it showed something like 0.17mW with the power set to full 1mW,
and i tuned the XV144 according to that. Only now i think about if that
display was really true i have tuned the XV to deliver max power at 1/5
input. Then maybe if Keying with the mike. are giving the 1mW no wonder i
overload the XV.
Thanks in advance
OZ1BZJ
BR.
Michael
On Tue Feb 21 13:11 , "Don Wilhelm" sent:
Michael,
Check the 'Firmware Requirements' section of the K60XV manual.
You must have Version 1.07 or later of the KSB2 firmware installed to
provide proper power level control when using SSB through the
low-power
output.
It does sound like you have an earlier version of the KSB2 firmware.
73,
Don W3FPR
> -----Original Message-----
>
> A question on the XV calibration.
>
> I am trying to align the XV144 using K2 with XV60 to drive the
> transverter. It is the QRP K2.
> When doing the alignment, there are several times need to key the
> K2 at the same time to tune on the transvert=r. For that reason I
> decided to use the tune on K2<=st1:place> to transmit as it will
> TX until I press the key again. All tune= up and the 20 W out was
> aligned.
>
> Now when I have connected a microphone to the K= and try a little
> USB I seem to drive the XV144 power in the r=d area. And I need
> turn down the power more then half to not have the red =ed on the
> XV144 on. So when=PA100 is installed the power transmitted from
> K2 can be less then the wanted power my the Power setting. Is
> somet=ing similar the case using the LOW power output of XV60
>
> If so what signal should I then use to tune the XV144 cw or a USB
> wher= I talk to the microphone?
>
Thanks in advance
>
> OZ1BZJ
>
> Michael Jensen
>
>
> _______________________________________________
> Elecraft mailing list
> Post to: [email protected]
> You must be a subscriber to post to the list.
> Subscriber Info (Addr. Change, sub, unsub etc.):
> http://mailman.qth.net/mailman/listinfo/elecraft
>
> Help: http://mailman.qth.net/subscribers.htm
> Elecraft web page: http://www.elecraft.com
>
>
> --
> No virus found in this incoming message.
> Checked by AVG Free Edition.
> Version: 7.1.375 / Virus Database: 267.15.11/264 - Release Date:
2/17/2006
>
>
=
_______________________________________________
Elecraft mailing list
Post to: [email protected]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
