Ed,
I don't know what audio card you are using, but if it has a stereo plug
on the KX3 end of the cable, it should not turn on PTT.
If it does, I suggest you make up a special cable with stereo plugs at
both ends, and connect only the tip and shell of the plugs.
That should eliminate your problems with PTT being activated in DATA A mode.
73,
Don W3FPR
On 2/19/2017 1:20 PM, Edouard Lafargue [email protected] [KX3] wrote:
Excellent news, Wayne!
If only you could consider making the "Mic Btn" settings
mode-dependent, my life would be complete (or thereabouts). Right now
this is the #1 setting I need to change all the time: when using the Mic
on SSB I have to enable "Ptt", and when switching to DATA to connect my
audio card for digital modes I need to set it to "Off" because the audio
card jack I use keys PTT... :)
73 de ed w6ela
On Fri, Feb 17, 2017 at 6:05 PM, Wayne Burdick <[email protected]
<mailto:[email protected]>> wrote:
Hi all,
Beta firmware rev. 2.70 is now available on our KX3 software page.
See release notes below for details.
For instructions on installing beta releases, refer to our KX3
software page. (Beta releases are not automatically recognized by
KX3 Utility.)
73,
Wayne
N6KR
* * *
MCU 2.70 / DSP 1.49, 2-17-2017
* AM TX BANDWIDTH INCREASED: The AM transmit bandwidth is now
approximately 100-4000 Hz (was 100-3000). TX EQ can be used to
further shape the passband.
* AM TX ALC IMPROVEMENTS: Fixed a bug in the AM power-control
algorithm that was causing power output to start too high, then
decrease over time when the operator is speaking. In addition, peak
power output is now displayed, rather than power/4 (25%). This is
intended to make the operator aware of the actual output from the
radio, which accounts for the observed current drain, stress on
dummy loads or antennas, etc.
* SCANNING WORKS WITH FREQUENCIES BELOW 1.0 MHz. Previously,
scanning would stall in this case.
For software developers:
* DT, FR, and FT HOST COMMANDS DISALLOWED IN TX MODE: Previously,
these commands (data submode, unsplit, and split) could be sent to
the K3 during transmit from software applications. This could
sometimes cause side effects such as muting of transmit audio in
DATA modes.
* RIT CLEAR SWITCH UPDATES RIT OFFSET AT PX3 PANADAPTER.
* POWER-OUTPUT CONTROL COMMAND (“PC”) FIXED: The PC command now
correctly handles the KX3’s power ranges (up to 12 W or 15 W
depending on band).
* PSK31/PSK63 SELECTION (ETC.) VIA REMOTE COMMAND: When the DATA
submode is being modified under remote control, a software
application can now select between PSK31/PSK63 using the UP/DN
control commands. Similarly, UPB/DNB can be used to select the
desired TEXT decode mode (DEC OFF, TX ONLY, RX THRn). To determine
the current state of any of these parameters, use the DS or DB
commands. Refer to the Programmer’s Reference.
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
<http://mailman.qth.net/mailman/listinfo/elecraft>
Help: http://mailman.qth.net/mmfaq.htm
<http://mailman.qth.net/mmfaq.htm>
Post: mailto:[email protected] <mailto:[email protected]>
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
<mailto:[email protected]>
__._,_.___
------------------------------------------------------------------------
Posted by: Edouard Lafargue <[email protected]>
------------------------------------------------------------------------
Reply via web post
<https://groups.yahoo.com/neo/groups/KX3/conversations/messages/61225;_ylc=X3oDMTJyajdtOG5iBF9TAzk3MzU5NzE0BGdycElkAzc0NTIwOTQ3BGdycHNwSWQDMTcwNTA2MzEwOARtc2dJZAM2MTIyNQRzZWMDZnRyBHNsawNycGx5BHN0aW1lAzE0ODc1Mjg0NTI-?act=reply&messageNum=61225>
• Reply to sender
<mailto:[email protected]?subject=Re%3A%20%5BElecraft%5D%20New%20KX3%20Beta%20Firmware%2C%20rev%2E%202%2E70%3A%20Various%20improvements>
• Reply to group
<mailto:[email protected]?subject=Re%3A%20%5BElecraft%5D%20New%20KX3%20Beta%20Firmware%2C%20rev%2E%202%2E70%3A%20Various%20improvements>
• Start a New Topic
<https://groups.yahoo.com/neo/groups/KX3/conversations/newtopic;_ylc=X3oDMTJma2ZxdWo3BF9TAzk3MzU5NzE0BGdycElkAzc0NTIwOTQ3BGdycHNwSWQDMTcwNTA2MzEwOARzZWMDZnRyBHNsawNudHBjBHN0aW1lAzE0ODc1Mjg0NTI->
• Messages in this topic
<https://groups.yahoo.com/neo/groups/KX3/conversations/topics/61206;_ylc=X3oDMTM3bjYzdGdnBF9TAzk3MzU5NzE0BGdycElkAzc0NTIwOTQ3BGdycHNwSWQDMTcwNTA2MzEwOARtc2dJZAM2MTIyNQRzZWMDZnRyBHNsawN2dHBjBHN0aW1lAzE0ODc1Mjg0NTIEdHBjSWQDNjEyMDY->
(2)
------------------------------------------------------------------------
Have you tried the highest rated email app? <https://yho.com/1wwmgg>
With 4.5 stars in iTunes, the Yahoo Mail app is the highest rated email
app on the market. What are you waiting for? Now you can access all your
inboxes (Gmail, Outlook, AOL and more) in one place. Never delete an
email again with 1000GB of free cloud storage.
------------------------------------------------------------------------
Visit Your Group
<https://groups.yahoo.com/neo/groups/KX3/info;_ylc=X3oDMTJma2ZybHRtBF9TAzk3MzU5NzE0BGdycElkAzc0NTIwOTQ3BGdycHNwSWQDMTcwNTA2MzEwOARzZWMDdnRsBHNsawN2Z2hwBHN0aW1lAzE0ODc1Mjg0NTI->
* New Members
<https://groups.yahoo.com/neo/groups/KX3/members/all;_ylc=X3oDMTJncDlucTUzBF9TAzk3MzU5NzE0BGdycElkAzc0NTIwOTQ3BGdycHNwSWQDMTcwNTA2MzEwOARzZWMDdnRsBHNsawN2bWJycwRzdGltZQMxNDg3NTI4NDUy>
12
* New Photos
<https://groups.yahoo.com/neo/groups/KX3/photos/photostream;_ylc=X3oDMTJnNDYxNnVrBF9TAzk3MzU5NzE0BGdycElkAzc0NTIwOTQ3BGdycHNwSWQDMTcwNTA2MzEwOARzZWMDdnRsBHNsawN2cGhvdARzdGltZQMxNDg3NTI4NDUy>
1
Yahoo! Groups
<https://groups.yahoo.com/neo;_ylc=X3oDMTJlM2JqbXZhBF9TAzk3NDc2NTkwBGdycElkAzc0NTIwOTQ3BGdycHNwSWQDMTcwNTA2MzEwOARzZWMDZnRyBHNsawNnZnAEc3RpbWUDMTQ4NzUyODQ1Mg-->
• Privacy <https://info.yahoo.com/privacy/us/yahoo/groups/details.html>
• Unsubscribe
<mailto:[email protected]?subject=Unsubscribe> • Terms of
Use <https://info.yahoo.com/legal/us/yahoo/utos/terms/>
.
__,_._,___
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
