> Before I could simply click in the log window for VFO A or on > a DX Spot and poof the TX arrow would point up. Then simply > click on a spot in the VFO B band map and poof you're on that > freq and you're TX arrow is pointing down. Almost felt like > a SO2R setup even though it was just SO2V.
Dual band receive works just fine (each VFO on a different band and "sub" on) as long as you are connecting a receive antenna to the AUX antenna jack or the sub receiver is on a lower band than the main receiver. You can change VFO B to a different band if you are in dual rx. What you can't do is split with VFO A and VFO B on different bands. The K3/KRC3 has always worked this way. The primary function of the N1MM Logger "SO2V" mode has always been to support "in band" SO2R operation. To my knowledge, there has not been any transceiver (with perhaps the exception of the FTdx9000) that provides full specification operation on two bands at the same time. The Orion/Orion II subreceiver is grossly inferior to the main receiver and the FT-1000MP could not listen on a separate band because it lacked independent bandpass filters for the subreceiver. 73, ... Joe, W4TV > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of Brett Howard > Sent: Saturday, June 20, 2009 2:42 AM > To: Elecraft List > Subject: Re: [Elecraft] SPL N/A with everybody on CW? > > > Wow I just tried doing an EE Init and set things up from > scratch for the beginning bit and then gave things a try and > I was still unable to get cross band split to work as it > should. This nearly makes using N1MM for SO2V nearly useless > and really degrades the usefulness of the KRX3. Man I sure > hope I can figure this out before FD! I was excited when it > was working before! > > Before I could simply click in the log window for VFO A or on > a DX Spot and poof the TX arrow would point up. Then simply > click on a spot in the VFO B band map and poof you're on that > freq and you're TX arrow is pointing down. Almost felt like > a SO2R setup even though it was just SO2V. > > :( > > ~KC7OTG > > On Fri, 2009-06-19 at 22:42 -0700, Brett Howard wrote: > > I should also state that I swear this was just working a minute ago > > and now I seem to always get SUB N/A unless both VFO's are > on the same > > band. > > > > On Fri, 2009-06-19 at 22:20 -0700, Brett Howard wrote: > > > Right now I've got VFO A on 14.030.00 and VFO B on > 7.027.00 and I'd > > > like to transmit on the VFO B freq. Or I'm trying to > setup N1MM so > > > that when I click on the VFO B log section that it > switches on split > > > so that I can TX in the right band. But I keep getting > SPL N/A. I > > > even then tapped > > > A->B twice and then went back to those frequencies and > still got SPL > > > N/A. Seems like I'm unable to use the split and TX on > VFO B if I'm > > > on independant bands? And yes both are set to CW. > > > > > > Any ideas what I'm doing wrong? > > > > > > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
