No, they are saved in the K3 EEPROM only. Dick, K6KR
Sent from my iPhone On Oct 6, 2009, at 1:08 PM, Brian Alsop <[email protected]> wrote: > Are the RF calibration values saved in the configuration file? > > Brian/K3KO > > > Wayne Burdick wrote: >> K3 beta-test firmware revision 3.41 (with DSP rev. 2.37) is now >> available. See release notes below. >> More refinements are in the works. But alas, it was time to "shoot >> the engineers" and get some interim feedback on the many new >> features in this revision. >> -------------- >> IMPORTANT NOTE >> -------------- >> The latest version of K3 Utility (1.2.9.30) must be used if you >> plan to do receiver RF gain calibration. You can find K3 Utility >> on our K3 software page, along with the K3 beta-test firmware: >> http://www.elecraft.com/K3/k3_software.htm >> Please send problem reports to [email protected]. >> 73, >> Wayne >> N6KR >> * * * >> MCU 3.41 / DSP 2.37, 10-02-2009 >> * IMPROVED RX LOW-FREQUENCY RESPONSE in AM/SSB/CW MODES: >> Most noticeable with hi-fidelity headphones or large speakers. >> NORMalizing >> the DSP passband still sets the cutoff to about 100 Hz, but DSP >> controls can >> be adjusted to provide a lower response. RX EQ can enhance bass >> further. >> * NO RX EQ OR TX EQ IN DATA MODES: That is, the response is flat >> (rolling off below 200 Hz). The RX EQ and TX EQ menu entries now >> affect only the other modes. >> * "LIVE" MEMORY RECALL (M>V): If you tap M>V, then start rotating >> VFO A to select a memory, the K3 will now switch to the band/mode >> of each memory. Exit memory recall by tapping M>V a second time. >> * VFO COARSE STEP ROUNDING: Tap '1' in the VFO CRS menu entry >> to select RND=NO or YES. If YES, the VFO frequency will be rounded >> off >> during COARSE tuning. This menu entry also sets the per-mode COARSE >> step size. Note: The RIT/XIT control moves the VFO in coarse steps if >> RIT and XIT are not in use (use CONFIG:VFO OFS to turn this on/off). >> * CWT (TUNING AID) NOW INDEPENDENT FOR CW & DATA. >> * RF GAIN CALIBRATION PROCEDURE UPDATED: You’ll need the >> latest revision of K3 Utility and a 50-microvolt signal source >> (e.g., an XG2). >> * SUB RX NOISE BLANKER NOW FULLY INDEPENDENT OF MAIN: >> This includes the on/off state and NB LEVEL settings. Note: Set >> CONFIG:NB SAVE to YES to preserve your per-band NB on/off settings. >> * DSP INTERNAL STATUS MONITORING: In the TECH MD menu entry, >> tapping 1 (main) or 2 (sub) displays DSP status information. If it >> is “FFFF”, >> no error has been detected. Tapping CLR resets the data to “FFF >> F”. >> * CHANNEL HOPPING IN FM MODE LOADS REPEATER SETTINGS: >> Repeater offsets and PL tones are now loaded during scanning/hopping. >> * PL TONE DEVIATION ADJUSTABLE: Tapping '1' in CONFIG:FM DEV >> allows setting PL tone deviation (300-600 Hz in 30-Hz steps; >> default, 360 Hz). >> * EU REPEATER 1750 HZ PL TONE BURST: If a 1750 Hz PL TONE is >> selected, a 500 ms tone burst will be sent on each PTT activation. >> * EXTENDED 6-METER TUNING RANGE: The VFO can now be tuned >> down to 44 MHz to monitor signals that may be correlated with 6-meter >> band openings. Loss increases rapidly below 49 MHz (-34 dB at 45 >> MHz), >> so a preamp (e.g., the Elecraft PR6) may be needed to obtain a >> useful NF. >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:[email protected] >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> --- >> --------------------------------------------------------------------- >> No virus found in this incoming message. >> Checked by AVG - www.avg.com Version: 8.5.420 / Virus Database: >> 270.14.4/2417 >> - Release Date: 10/06/09 06:50:00 > > No virus found in this outgoing message. > Checked by AVG - www.avg.com > Version: 8.5.420 / Virus Database: 270.14.4/2417 - Release Date: > 10/06/09 06:50:00 > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
