Hello everyone! I try to install the driver under opensuse 10.3 and 11.0. Both systems are installed fresh and the failure comes also with all updates installed. When i plug in the device the driver look like loaded OK the dmesg:
------------------------------------------------------------------------------------ usb 6-1: new high speed USB device using ehci_hcd and address 2 usb 6-1: configuration #1 chosen from 1 choice usb 6-1: New USB device found, idVendor=0ccd, idProduct=0072 usb 6-1: New USB device strings: Mfr=0, Product=1, SerialNumber=2 usb 6-1: Product: Cinergy Hybrid T USB XS FM usb 6-1: SerialNumber: 080102004516 Linux video capture interface: v2.00 em28xx v4l2 driver version 0.0.1 loaded em28xx new video device (0ccd:0072): interface 0, class 255 em28xx: device is attached to a USB 2.0 bus em28xx #0: Alternate settings: 8 em28xx #0: Alternate setting 0, max size= 0 em28xx #0: Alternate setting 1, max size= 0 em28xx #0: Alternate setting 2, max size= 1448 em28xx #0: Alternate setting 3, max size= 2048 em28xx #0: Alternate setting 4, max size= 2304 em28xx #0: Alternate setting 5, max size= 2580 em28xx #0: Alternate setting 6, max size= 2892 em28xx #0: Alternate setting 7, max size= 3072 device has gpio reset values stored on board cx25843.c: starting probe for adapter SMBus I801 adapter at 1c20 (0x40004) cx25843.c: detecting cx25843 client on address 0x88 input: em2880/em2870 remote control as /devices/virtual/input/input7 em28xx-input.c: remote control handler attached cx25843.c: starting probe for adapter em28xx #0 (0x1001f) cx25843.c: detecting cx25843 client on address 0x88 attach_inform: msp34xx/cx25843 detected. trying to attach xc5000 attaching xc5000 tuner module successfully attached tuner radio device registered as /dev/radio0 em28xx #0: AC97 command still being executed: not handled properly! em28xx #0: V4L2 VBI device registered as /dev/vbi0 em28xx #0: V4L2 device registered as /dev/video0 em28xx #0: Found Terratec Hybrid XS FM (em2883) usbcore: registered new interface driver em28xx radio open() modelock active! vbi open() modelock active! analog tv open() modelock active! tuner' 1-0061: chip found @ 0xc2 (em28xx #0) attach inform (default): detected I2C address c2 em28xx-audio.c: probing for em28x1 non standard usbaudio em28xx-audio.c: Copyright (C) 2006 Markus Rechberger Em28xx: Initialized (Em28xx Audio Extension) extension em2880-dvb.c: DVB Init DVB: registering new adapter (em2880 DVB-T) DVB: registering frontend 0 (Zarlink ZL10353 DVB-T)... Em28xx: Initialized (Em2880 DVB Extension) extension ----------------------------------------------------------------------------------------------------- at next when i start the dvb section in kaffeine nothing will happend and the commandline from kaffeine and the dmesg tells me following: ----------------------------------------------------------------------------------------------------- [EMAIL PROTECTED]:~> kaffeine /dev/dvb/adapter0/frontend0 : opened ( Zarlink ZL10353 DVB-T ) 0 EPG plugins loaded for device 0:0. Loaded epg data : 4134 events (56 msecs) [EMAIL PROTECTED]:~> Tuning to: RTL2 / autocount: 0 DvbCam::probe(): /dev/dvb/adapter0/ca0: : Datei oder Verzeichnis nicht gefunden Using DVB device 0:0 "Zarlink ZL10353 DVB-T" tuning DVB-T to 538000000 Hz inv:2 bw:0 fecH:2 fecL:9 mod:1 tm:1 gi:3 hier:0 ...... Not able to lock to the signal on the given frequency Frontend closed Tuning delay: 1139 ms dmesg: SFW2-INext-DROP-DEFLT IN=vmnet1 OUT= MAC= SRC=172.16.54.1 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44 SFW2-INext-DROP-DEFLT IN=vmnet8 OUT= MAC= SRC=192.168.23.1 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44 SFW2-INext-DROP-DEFLT IN=wlan0 OUT= MAC= SRC=192.168.2.104 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44 initializing: 18 powered down zl10353 initializing: 18 FIXME:em28xx_i2c_send_bytes(c2): write failed: =============================== 00 00 00 00 ================================ FIXME:em28xx_i2c_send_bytes(c2): write failed: =============================== 00 01 80 0b ================================ FIXME:em28xx_i2c_send_bytes(c2): write failed: =============================== 00 02 00 c0 ================================ FIXME:em28xx_i2c_send_bytes(c2): write failed: =============================== 00 05 12 3d ================================ FIXME:em28xx_i2c_send_bytes(c2): write failed: =============================== 00 03 85 d0 ================================ FIXME:em28xx_i2c_send_bytes(c2): write failed: =============================== 00 0a 00 00 ================================ powered down zl10353 ------------------------------------------------------------------------------------ With the application running i must unplug/plugin the device and then is everthing is OK. I can change channels and watch TV until i stop the TV watching. Next attempt same problem and i have done the same procedure. -------------------------------------------------------------------------------------- kaffeine after plug out/in without closing program Tuning to: RTL2 / autocount: 0 Using DVB device 0:0 "Zarlink ZL10353 DVB-T" tuning DVB-T to 538000000 Hz inv:2 bw:0 fecH:2 fecL:9 mod:1 tm:1 gi:3 hier:0 ... LOCKED. NOUT: 1 dvbEvents 0:0 started Tuning delay: 781 ms pipe opened xine pipe opened /home/sfi/.kaxtv.ts ---------------------------------------------------------------------------------------------------- The problem still exists also with other programs eg. mplayer, xine ore the scan tool for a channel.conf. and as root logged in. I hope anyone has a solution for this problem and can help me! -Stefan _______________________________________________ Em28xx mailing list [email protected] http://mcentral.de/mailman/listinfo/em28xx
