Dear John, In IEC 60950-1 in clause 1.6.2 you can find following definition:
In each case, the readings are taken when the input current has stabilized. If the current varies during the normal operating cycle, the steady-state current is taken as the mean indication of the value, measured on a recording r.m.s. ammeter, during a representativeperiod. Boštjan Glavič Vodja laboratorija, Laboratorij za elektroniko Head of Laboratory, Laboratory of Electronic Engineering [SIQlogo60px] www.siq.si<http://www.siq.si/> SIQ Ljubljana, Trzaska c. 2, SI-1000 Ljubljana, Slovenia, VAT ID: SI23509678 t +386 (0)1 4778 265<tel:+386%20(0)1%204778%20265>, m +386 (0)41 391 283<tel:+386%20(0)41%20391%20283>, f +386 (0)1 4778 444<tel:+386%20(0)1%204778%20444> On 9. avg. 2014, at 11:55, "John Woodgate" <[email protected]<mailto:[email protected]>> wrote: In message <[email protected]<mailto:[email protected]>>, dated Sat, 9 Aug 2014, =?iso-8859-2?Q?Bo=B9tjan_Glavi=E8?= <[email protected]<mailto:[email protected]>> writes: Please check clause E.1 in IEC 62368-1. I believe requirements in IEC 60065 are exactly the same. You need to use 1kHz source to verify what input signal amplitude results in output clipping. Then you need to set 1/8 of maximum non clipped output power with pink noise on input. Thank you, but I asked specifically about the *definitions* of the two terms, which I don't think are in the standards you mention. For example, 60065 uses the term 'non-clipped output power'. -- OOO - Own Opinions Only. With best wishes. See www.jmwa.demon.co.uk<http://www.jmwa.demon.co.uk> Quid faciamus nisi sit? John Woodgate, J M Woodgate and Associates, Rayleigh, Essex UK - ---------------------------------------------------------------- This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. To post a message to the list, send your e-mail to <[email protected]<mailto:[email protected]>> All emc-pstc postings are archived and searchable on the web at: http://www.ieee-pses.org/emc-pstc.html Attachments are not permitted but the IEEE PSES Online Communities site at http://product-compliance.oc.ieee.org/ can be used for graphics (in well-used formats), large files, etc. Website: http://www.ieee-pses.org/ Instructions: http://www.ieee-pses.org/list.html (including how to unsubscribe) List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas <[email protected]<mailto:[email protected]>> Mike Cantwell <[email protected]<mailto:[email protected]>> For policy questions, send mail to: Jim Bacher: <[email protected]<mailto:[email protected]>> David Heald: <[email protected]<mailto:[email protected]>> - ---------------------------------------------------------------- This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. To post a message to the list, send your e-mail to <[email protected]> All emc-pstc postings are archived and searchable on the web at: http://www.ieee-pses.org/emc-pstc.html Attachments are not permitted but the IEEE PSES Online Communities site at http://product-compliance.oc.ieee.org/ can be used for graphics (in well-used formats), large files, etc. Website: http://www.ieee-pses.org/ Instructions: http://www.ieee-pses.org/list.html (including how to unsubscribe) List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas <[email protected]> Mike Cantwell <[email protected]> For policy questions, send mail to: Jim Bacher: <[email protected]> David Heald: <[email protected]>
