Hi there
could you show me your dmesg and your lspci out put please!
I tried changing the jumpers but nothing happened
btw I also have the analog card
also I read the integrators manual as well.
loadrt hal_motenc
did nothing.
I´ll be testing on windows later today and asking here more questions
thanks for the answers
On Thu, Feb 21, 2008 at 9:58 PM, Dave Keeton <[EMAIL PROTECTED]> wrote:
> I have installed the same board with no problems, Running on the
> following.....
>
> Pentium4, 2ghz Dell Diminsion 8200 with 768megs of ram. First I installed
> the card with default jumper settings and then loaded EMC 2.2.2. All I/Os
> work fine. It should be set for board ID "0".....EMC will not run at all
> with the board removed using the Motenc config files. You should get error
> messages.....Did you also buy the 8/16 I/O boards and the analog card?
>
> Dave Keeton
>
> ----- Original Message -----
> *From:* Dave Engvall <[EMAIL PROTECTED]>
> *To:* Enhanced Machine Controller (EMC) <emc-users@lists.sourceforge.net>
> *Sent:* Thursday, February 21, 2008 7:07 PM
> *Subject:* Re: [Emc-users] not recognized motenc-lite card
>
> Hi,
> You might try checking the board ID jumpers; it looks like both need to be
> in place for board 0.
> I don't have a -Lite board but do have the 8 channel board.
> Try starting emc with the board not installed and see if you get a message
> something like "board not found" or "board not installed". Usually almost
> the last thing in the error window.
>
> Then check the jumpers, install the board and go again.
>
> The "Lite" board was used in the Mazak conversion at Fest and worked quite
> well. Check the wiki for more information on the conversion.
>
> Good luck.
>
> Dave
>
>
>
> On Feb 21, 2008, at 12:52 PM, cnc eafit wrote:
>
> Hi there
> I just bought a Motenc-lite card that is suposoused to be supported by
> linuxcnc. But when I booted the system it does not come up. I'm totally
> lost I've been unable to find documentation to fix the problem.
>
>
> thanks in advance
>
>
> CARD:
> MOTENC-Lite 4 axes PCI MOTION & I/O control board
>
> linuxcnc installed form the lastest cd and updated to 2.2.3
>
> lspci
> 0000:02:07.0 Bridge: PLX Technology, Inc.: Unknown device 3001 (rev 01)
> <emc-users@lists.sourceforge.net>
>
>
> <emc-users@lists.sourceforge.net> <emc-users@lists.sourceforge.net>
> -------------------------------------------------------------------------
> This SF.net email is sponsored by: Microsoft
> Defy all challenges. Microsoft(R) Visual Studio 2008.
>
> http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/_______________________________________________
> Emc-users mailing list
> Emc-users@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/emc-users
>
>
> ------------------------------
>
> -------------------------------------------------------------------------
> This SF.net email is sponsored by: Microsoft
> Defy all challenges. Microsoft(R) Visual Studio 2008.
> http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
>
> ------------------------------
>
> _______________________________________________
> Emc-users mailing list
> Emc-users@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/emc-users
>
>
> -------------------------------------------------------------------------
> This SF.net email is sponsored by: Microsoft
> Defy all challenges. Microsoft(R) Visual Studio 2008.
> http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
> _______________________________________________
> Emc-users mailing list
> Emc-users@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/emc-users
>
>
-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2008.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
