Hi,
Let's drop back one step. Download vsitest.c and compile it. It is a
primitive diagnostic much like the ones for ppmc or stg. If you get
that to work then the problem is not the card but something in the
driver (unlikely) or
the .ini.
Use this link:
http://www.vitalsystem.com/web/motion/motionLite.php
then select "Linux code".
Keep kicking at it; you will get it to work.
Dave
On Feb 22, 2008, at 9:06 AM, cnc eafit wrote:
Hi there
could you show me your dmesg and your lspci out put please!
I tried changing the jumpers but nothing happened
btw I also have the analog card
also I read the integrators manual as well.
loadrt hal_motenc
did nothing.
I´ll be testing on windows later today and asking here more
questions
thanks for the answers
On Thu, Feb 21, 2008 at 9:58 PM, Dave Keeton <[EMAIL PROTECTED]>
wrote:
I have installed the same board with no problems, Running on the
following.....
Pentium4, 2ghz Dell Diminsion 8200 with 768megs of ram. First I
installed the card with default jumper settings and then loaded EMC
2.2.2. All I/Os work fine. It should be set for board ID
"0".....EMC will not run at all with the board removed using the
Motenc config files. You should get error messages.....Did you also
buy the 8/16 I/O boards and the analog card?
Dave Keeton
----- Original Message -----
From: Dave Engvall
To: Enhanced Machine Controller (EMC)
Sent: Thursday, February 21, 2008 7:07 PM
Subject: Re: [Emc-users] not recognized motenc-lite card
Hi,
You might try checking the board ID jumpers; it looks like both
need to be in place for board 0.
I don't have a -Lite board but do have the 8 channel board.
Try starting emc with the board not installed and see if you get a
message something like "board not found" or "board not installed".
Usually almost the last thing in the error window.
Then check the jumpers, install the board and go again.
The "Lite" board was used in the Mazak conversion at Fest and
worked quite well. Check the wiki for more information on the
conversion.
Good luck.
Dave
On Feb 21, 2008, at 12:52 PM, cnc eafit wrote:
Hi there
I just bought a Motenc-lite card that is suposoused to be
supported by linuxcnc. But when I booted the system it does not
come up. I'm totally lost I've been unable to find documentation
to fix the problem.
thanks in advance
CARD:
MOTENC-Lite 4 axes PCI MOTION & I/O control board
linuxcnc installed form the lastest cd and updated to 2.2.3
lspci
0000:02:07.0 Bridge: PLX Technology, Inc.: Unknown device 3001
(rev 01)
---------------------------------------------------------------------
----
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2008.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
----------------------------------------------------------------------
---
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2008.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
----------------------------------------------------------------------
---
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2008.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
----------------------------------------------------------------------
---
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2008.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2008.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
