You mean that the tool is on the inside of the arc?

> -----Original Message-----
> From: Sam Sokolik [mailto:samco...@gmail.com]
> Sent: March-30-21 4:55 PM
> To: Enhanced Machine Controller (EMC)
> Subject: Re: [Emc-users] Rotary axis preview (in axis interface)
> 
> This might make a bit more sense of what I am talking about..
> 
> http://electronicsam.com/images/greenmachine/Screenshot_2021-03-30_18-53-52.png
> 
> On Tue, Mar 30, 2021 at 6:51 PM Sam Sokolik <samco...@gmail.com> wrote:
> 
> > it makes it so the bounding box doesn;t really make sense,,,
> >
> >
> > http://electronicsam.com/images/greenmachine/Screenshot_2021-03-30_18-50-41.png
> >
> > On Tue, Mar 30, 2021 at 6:44 PM Sam Sokolik <samco...@gmail.com> wrote:
> >
> >>
> >> http://electronicsam.com/images/greenmachine/Screenshot_2021-03-30_18-00-14.png
> >>
> >> that is the screenshot - the gcode from andy is here..
> >>
> >>
> >> https://forum.linuxcnc.org/20-g-code/27169-g-code-to-engrave-numbers-on-cylinders?start=0
> >>
> >> On Tue, Mar 30, 2021 at 6:38 PM John Dammeyer <jo...@autoartisans.com>
> >> wrote:
> >>
> >>> Photo yes.  No G Code if that was supposed to be attached.  I find when
> >>> I run the CAM simulation on VisualCAM (AlibreCAM) that the tool moves
> >>> around the work piece rather than the work piece image rotating.  If 
> >>> that's
> >>> what you meant.
> >>> If you attach the G-Code I can try it here on my A axis.
> >>> John
> >>>
> >>> > -----Original Message-----
> >>> > From: Sam Sokolik [mailto:samco...@gmail.com]
> >>> > Sent: March-30-21 4:05 PM
> >>> > To: Enhanced Machine Controller (EMC)
> >>> > Subject: [Emc-users] Rotary axis preview (in axis interface)
> >>> >
> >>> > Has anyone done work on the preview for a 4th axis mounted on the
> >>> table?
> >>> >  I feel like in this situation - the gcode preview should be spinning
> >>> while
> >>> > the tool tip stay stationary...  Uless I have the geometry set wrong -
> >>> but
> >>> > currently I have it set to AXYZ.  I think I have tried all
> >>> compinations -
> >>> > but the tool seems to move around the gcode - instead of the gcode
> >>> moving
> >>> > around the tool...
> >>> >
> >>> > http://electronicsam.com/images/greenmachine/IMG_20210329_220745.jpg
> >>> >
> >>> > sam
> >>> >
> >>> > let me know if the attachment comes through...
> >>>
> >>>
> >>>
> >>> _______________________________________________
> >>> Emc-users mailing list
> >>> Emc-users@lists.sourceforge.net
> >>> https://lists.sourceforge.net/lists/listinfo/emc-users
> >>>
> >>
> 
> _______________________________________________
> Emc-users mailing list
> Emc-users@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/emc-users



_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users

Reply via email to