At 72-73 my sill is NOT level, about a bubble width off level yet.
--- In [email protected], Caliendo Dan <djcalie...@...> wrote: > > I know mine is around 72"; but level at the window sill. No problem with > cross wind landings. > Dan C > > On May 26, 2010, at 11:38 AM, Donald wrote: > > > > > > > I give up. The main tires are at 20, the nose at 15, still get 72-73 inches > > on tail height. I really wonder how many people have actually measured or > > leveled theirs. Surely I am not alone in this. > > > > --- In [email protected], "Donald" <DonGeneda@> wrote: > > > > > > > > > > > > Very level concrete floor. Somewhere I read what the strut amount showing > > > on the front gear was, and mine was correct. I cannot recall the > > > measurements now. I am going out this morning with a tire pressure check, > > > although the main tires look OK. > > > Maybe a set of "Tundra Tires" on the mains is in order. > > > > > > --- In [email protected], Caliendo Dan <djcaliendo@> wrote: > > > > > > > > Is your front strut not going down as far as it should? That will lower > > > > the nose. > > > > Is the floor you plane is sitting on level? > > > > Dan C > > > > > > > > On May 25, 2010, at 8:05 PM, Donald wrote: > > > > > > > > > > > > > > > > > > > I feel like that comic strip character with the black cloud raining > > > > > on him and following him around. > > > > > I got the used belleville struts with spacers all serviced and > > > > > installed today, let it down on its wheels again and could see the > > > > > wingtips were higher, hurried around to the tail with a tape measure, > > > > > now it is 72 inches tall, did not gain much. Window sill is not level > > > > > either. I don't know what is next, add more spacers? Is there a limit > > > > > to spacers? I am going to check main tire pressures tomorrow, maybe I > > > > > can get some help there. > > > > > > > > > > --- In [email protected], "Donald" <DonGeneda@> wrote: > > > > > > > > > > > > > > > > > > > > > > > > I would have to assume that the rusting happens on the upper > > > > > > exposed part of the piston over time and smooth landings. Then > > > > > > comes one of those teeth jarring landings, and the rusty piston is > > > > > > forced into the strut body with force - and it don't come back. > > > > > > Once stuck there with rust, it only gets worse with time. Just a > > > > > > guess, and I too was surprised with the number of people who have > > > > > > experienced this. Certainly an area to be checked often. > > > > > > For those who have not done it, taking the strut apart, leaving the > > > > > > piston on the wing, is a very quick and easy operation for anyone. > > > > > > Dressing the upper portion with some emery cloth if rusty could > > > > > > well keep you from being in the same shape I am in now. It is the > > > > > > old "stich in time saves nine" type thing. > > > > > > > > > > > > --- In [email protected], "Hartmut Beil" <hbeil@> wrote: > > > > > > > > > > > > > > Dave . He has a used one pair ready, but he can't get the old one > > > > > > > out! > > > > > > > Now there are already three folks on the list that had rusted > > > > > > > solid struts. > > > > > > > > > > > > > > I was under the impression that these struts could run low on > > > > > > > fluid, but rusting solid, that's new to me. > > > > > > > > > > > > > > Hartmut > > > > > > > > > > > > > > > > > > > > > From: bigbrownpilot@ > > > > > > > Sent: Monday, May 24, 2010 4:33 AM > > > > > > > To: [email protected] > > > > > > > Subject: [ercoupe-tech] Re: MLG Problems, long post, Need Help! > > > > > > > > > > > > > > > > > > > > > > > > > > > > Finally, someone has a problem that I don't have! > > > > > > > > > > > > > > Wonder if you can find a new/used pair of oleos? > > > > > > > > > > > > > > --- In [email protected], "Donald" <DonGeneda@> wrote: > > > > > > > > > > > > > > > > Fitting in with the MLG postings of late, I decidewd to jack > > > > > > > > mine up and put in the spacers to raise my tail today. As I was > > > > > > > > taking thinga apart, I was surprised to see there were already > > > > > > > > a set of spacers there. Strange, my tail is pretty low. > > > > > > > > I decided to measure my donut stack, three and 1/2 inches, > > > > > > > > although the rubbers look as good as new. I jacked it up to > > > > > > > > measure again no load - still three and a half! What the heck > > > > > > > > is going on here. I have a pair of bellville spring equipped > > > > > > > > struts, measured them, and the stack is about four and a > > > > > > > > quarter inches! > > > > > > > > I decide to take things apart to see what is going on, drop the > > > > > > > > bottom bolt, swing the strut back to pull it off - and it won't > > > > > > > > move! Now I understand why the rubbers are compressed - the > > > > > > > > strut is froze solid in a compressed state! Take the other side > > > > > > > > off, same thing. > > > > > > > > Easy, just pull the top bolt out - whoops, I think you must > > > > > > > > have to pull the wings to do that AND have some special > > > > > > > > wrenches, not what I wanted. I found I could put a drift down > > > > > > > > thru between the wing and center section, and pound on the top > > > > > > > > of the strut to try to beat the bottom part off. No luck, gave > > > > > > > > up for the day and came home to get a bigger hammer - a LOT > > > > > > > > BIGGER hammer. I may have to heat the outside of the strut to > > > > > > > > release it, probably burn up the rubbers, and I don't even know > > > > > > > > for sure WHERE the sticking is! > > > > > > > > Has anybody else had this problem? I could sure use an easy > > > > > > > > solution right now. > > > > > > > > No wonder I had such a devil of a time with smooth landings, > > > > > > > > darned thing had NO spring action whatever! > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
