Mike,
I do not own an IDE/ATAPI CDROM.
Half of my hardware is SCSI
My conf.module looks like this:
alias scsi_hostadapter aic7xxx
alias eth0 tulip
alias eth1 tulip
alias parport_lowlevel parport_pc
alias sound es1371
pre-install pcmcia_core /etc/rc.d/init.d/pcmcia start
pre-install plip modprobe parport_pc ; echo 7 > /proc/parport/0/irq
post-install supermount modprobe scsi_hostadapter
I'm wondering if I should add something like this, change line 1 to:
alias scsi_hostadapter aic7xxx, ide-scsi
But, I just don't know.
Mike Hahn wrote:
> First, is it ATAPI? If so you may want to try these changes in your kernel
> configuration:
> Under Block Devices:
> 1) turning off IDE/ATAPI CDROM support
> 2) enable SCSI emulation support
> Under SCSI support
> 1) enable SCSI CD-ROM support
> 2) enable SCSI generic support
>
> Then recompile and install the new kernel. I had the same problem
> although my cdrom is internal, I read somewhere that if your kernel sees
> an ATAPI cdrom it will load it first and disregard SCSI support. Also
> make sure you have the line:
>
> append = "hd?=ide-scsi"
>
> in your lilo.conf file . Obviously replace the ? with the logical drive.
>
> Hope this helps
>
> Mike Hahn
>
> silkythreads wrote:
>
> > I have MANDRAKE 7.0, Kernel 2.2.14-15mdk installed.
> >
> > Everything works EXCEPT .......my HP 7200e (that;'s external)
> >
> > I've tried it, it does not work. Only my scsi cdrom responds.
> >
> > Here's my story ......
> >
> > Internal hardware:
> >
> > hda: Maxtor 91360D9, ATA DISK drive
> > hdb: WDC AC33100H, ATA DISK drive
> > hdc: LS-120 CSMO 05 UHD Floppy, ATAPI FLOPPY drive
> >
> > I have internal SCSI installed
> >
> > scsi id 5 PLEXTOR CD-ROM PX-32TS - This is my primary CDROM
> > scsi id 6 IBM DCAS-34330W - This is my primary HARDDRIVE (2 parts -
> >
> > sda1, sda5)
> >
> > parport is installed. I have an external HP 694C printer on the end of
> > my
> > parallel port chain.
> >
> > My HP 7200e is in between the computer and printer.
> >
> > I can not get my computer to recognize my cdrw.
> >
> > I've tried "mount -t iso9660 /dev/scd0 /mnt/cdrw"
> > And it only re-mounts my primary cdrom, which of course is now mounted
> > twice.
> > (Actually, I tried everything I've read and more than I wanted too.)
> >
> > I keep thinking that if the CDRW requires ide-scsi support, I should try
> >
> > and make my scsi adapter see it, to define an ID for it.
> >
> > HELP !! I CAN NOT GET THIS TO WORK, and I'll bet it's something
> > SO SIMPLY !!
> >
> > Included with this request for HELP is a copy of my dmesg and fstab
> > file.
> >
> > Thanks for creative suggestions.
> >
> > BTY - I've read all the documentation and ton's of newsgroup postings,
> > NOTHING has helped so far.
> >
> > ***********************************************************************
> > dmesg output
> > ***********************************************************************
> > Linux version 2.2.14-15mdk ([EMAIL PROTECTED]) (gcc version
> > 2.95.2 19991024 (release)) #1 Tue Jan 4 22:24:20 CET 2000
> > relocating initrd image:
> > initrd_start:0xc0fa5000 initrd_end:0xc0fff270
> > mem_start:0xc026d000 mem_end:0xcfff0000
> > initrd_size:0x0005a270 dest:0xcff95000
> > Detected 348489026 Hz processor.
> > Console: colour VGA+ 80x25
> > Calibrating delay loop... 347.34 BogoMIPS
> > Memory: 257252k/262080k available (1092k kernel code, 416k reserved,
> > 2892k data, 64k init, 0k bigmem)
> > Dentry hash table entries: 262144 (order 9, 2048k)
> > Buffer cache hash table entries: 262144 (order 8, 1024k)
> > Page cache hash table entries: 65536 (order 6, 256k)
> > VFS: Diskquotas version dquot_6.4.0 initialized
> > CPU: Intel Pentium II (Deschutes) stepping 01
> > Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
> >
> > Checking 'hlt' instruction... OK.
> > POSIX conformance testing by UNIFIX
> > mtrr: v1.35a (19990819) Richard Gooch ([EMAIL PROTECTED])
> > PCI: PCI BIOS revision 2.10 entry at 0xfd993
> > PCI: Using configuration type 1
> > PCI: Probing PCI hardware
> > PCI: Enabling I/O for device 00:60
> > PCI: Enabling I/O for device 00:70
> > PCI: Enabling memory for device 00:70
> > PCI: Enabling I/O for device 00:78
> > PCI: Enabling memory for device 00:78
> > Linux NET4.0 for Linux 2.2
> > Based upon Swansea University Computer Society NET3.039
> > NET4: Unix domain sockets 1.0 for Linux NET4.0.
> > NET4: Linux TCP/IP 1.0 for NET4.0
> > IP Protocols: ICMP, UDP, TCP, IGMP
> > TCP: Hash tables configured (ehash 262144 bhash 65536)
> > Initializing RT netlink socket
> > Starting kswapd v 1.5
> > Detected PS/2 Mouse Port.
> > Serial driver version 4.27 with MANY_PORTS MULTIPORT SHARE_IRQ enabled
> > ttyS00 at 0x03f8 (irq = 4) is a 16550A
> > pty: 256 Unix98 ptys configured
> > apm: BIOS version 1.2 Flags 0x03 (Driver version 1.9)
> > Real Time Clock Driver v1.09
> > RAM disk driver initialized: 16 RAM disks of 4096K size
> > PIIX4: IDE controller on PCI bus 00 dev 39
> > PIIX4: not 100% native mode: will probe irqs later
> > ide0: BM-DMA at 0x1000-0x1007, BIOS settings: hda:DMA, hdb:pio
> > ide1: BM-DMA at 0x1008-0x100f, BIOS settings: hdc:pio, hdd:pio
> > hd0: C/H/S=27625/247/228 from BIOS ignored
> > hda: Maxtor 91360D8, ATA DISK drive
> > hdb: WDC AC33100H, ATA DISK drive
> > hdc: LS-120 CSMO 05 UHD Floppy, ATAPI FLOPPY drive
> > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> > ide1 at 0x170-0x177,0x376 on irq 15
> > hda: Maxtor 91360D8, 12970MB w/256kB Cache, CHS=26353/16/63
> > hdb: WDC AC33100H, 3020MB w/128kB Cache, CHS=1024/255/63
> > Floppy drive(s): fd0 is 1.44M
> > FDC 0 is a post-1991 82077
> > md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12
> > raid5: measuring checksumming speed
> > raid5: MMX detected, trying high-speed MMX checksum routines
> > pII_mmx : 768.477 MB/sec
> > p5_mmx : 803.910 MB/sec
> > 8regs : 622.935 MB/sec
> > 32regs : 328.041 MB/sec
> > using fastest function: p5_mmx (803.910 MB/sec)
> > scsi : 0 hosts.
> > scsi : detected total.
> > md.c: sizeof(mdp_super_t) = 4096
> > Partition check:
> > hda: [PTBL] [1653/255/63] hda1 hda2 < hda5 hda6 hda7 hda8 hda9 >
> > hdb: hdb1 hdb2 < hdb5 hdb6 hdb7 hdb8 hdb9 hdb10 hdb11 hdb12 hdb13 >
> > RAMDISK: Compressed image found at block 0
> > autodetecting RAID arrays
> > autorun ...
> > ... autorun DONE.
> > VFS: Mounted root (ext2 filesystem).
> > (scsi0) <Adaptec AHA-294X Ultra SCSI host adapter> found at PCI 13/0
> > (scsi0) Wide Channel, SCSI ID=7, 16/255 SCBs
> > (scsi0) Warning - detected auto-termination
> > (scsi0) Please verify driver detected settings are correct.
> > (scsi0) If not, then please properly set the device termination
> > (scsi0) in the Adaptec SCSI BIOS by hitting CTRL-A when prompted
> > (scsi0) during machine bootup.
> > (scsi0) Cables present (Int-50 YES, Int-68 YES, Ext-68 NO)
> > (scsi0) Downloading sequencer code... 413 instructions downloaded
> > scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.21/3.2.4
> > <Adaptec AHA-294X Ultra SCSI host adapter>
> > scsi : 1 host.
> > (scsi0:0:5:0) Synchronous at 20.0 Mbyte/sec, offset 15.
> > Vendor: PLEXTOR Model: CD-ROM PX-32TS Rev: 1.02
> > Type: CD-ROM ANSI SCSI revision: 02
> > Detected scsi CD-ROM sr0 at scsi0, channel 0, id 5, lun 0
> > (scsi0:0:6:0) Synchronous at 40.0 Mbyte/sec, offset 8.
> > Vendor: IBM Model: DCAS-34330W Rev: S65A
> > Type: Direct-Access ANSI SCSI revision: 02
> > Detected scsi disk sda at scsi0, channel 0, id 6, lun 0
> > Uniform CDROM driver Revision: 2.56
> > SCSI device sda: hdwr sector= 512 bytes. Sectors= 8467200 [4134 MB] [4.1
> > GB]
> > sda: sda1 sda2 < sda5 >
> > tulip.c:v0.91g-ppc 7/16/99 [EMAIL PROTECTED]
> > eth0: Lite-On 82c168 PNIC rev 32 at 0x1800, 00:A0:CC:57:0D:AD, IRQ 11.
> > eth0: MII transceiver #1 config 3000 status 7829 advertising 01e1.
> > eth1: Lite-On 82c168 PNIC rev 33 at 0x2000, 00:A0:CC:3E:24:6F, IRQ 10.
> > eth1: MII transceiver #1 config 1000 status 782d advertising 01e1.
> > autodetecting RAID arrays
> > autorun ...
> > ... autorun DONE.
> > VFS: Mounted root (ext2 filesystem) readonly.
> > change_root: old root has d_count=1
> > Trying to unmount old root ... okay
> > Freeing unused kernel memory: 64k freed
> > Adding Swap: 133016k swap-space (priority -1)
> > es1371: version v0.19 time 22:34:23 Jan 4 2000
> > es1371: found adapter at io 0x1040 irq 11
> > es1371: features: joystick 0x0
> > es1371: codec vendor CRY revision 3
> > es1371: codec features Headphone out 18bit DAC 18bit ADC
> > es1371: stereo enhancement: no 3D stereo enhancement
> > cdrom: open failed.
> > VFS: Disk change detected on device sr(11,0)
> > VFS: Disk change detected on device fd(2,0)
> > [MS-DOS FS Rel. 12,FAT 0,check=n,conv=b,uid=0,gid=0,umask=022,bmap]
> >
>[me=0xfe,cs=0,#f=0,fs=1810,fl=144680,ds=1810,de=0,data=1810,se=28672,ts=940114177,ls=5120,rc=0,fc=4294967295]
> >
> > Transaction block size = 512
> > VFS: Can't find a valid MSDOS filesystem on dev 02:00.
> > parport0: PC-style at 0x378 [SPP,PS2,EPP]
> > parport0: Printer, HEWLETT-PACKARD DESKJET 690C
> > lp0: using parport0 (polling).
> >
> > ***********************************************************************
> > FSTAB file
> > ***********************************************************************
> >
> > none /proc proc defaults 0 0
> > none /dev/pts devpts mode=0620 0 0
> > /dev/hda1 /mnt/DOS_hda1 vfat user,exec,conv=auto 0 0
> > /dev/hda5 /mnt/DOS_hda5 vfat user,exec,conv=auto 0 0
> > /dev/hda6 /mnt/DOS_hda6 vfat user,exec,conv=auto 0 0
> > /dev/hda7 /mnt/DOS_hda7 vfat user,exec,conv=auto 0 0
> > /dev/hda8 /mnt/DOS_hda8 vfat user,exec,conv=auto 0 0
> > /dev/hda9 /mnt/DOS_hda9 vfat user,exec,conv=auto 0 0
> > /dev/hdb1 /boot ext2 defaults 1 2
> > /dev/hdb5 /usr ext2 defaults 1 2
> > /dev/hdb6 /usr/local ext2 defaults 1 2
> > /dev/hdb7 /home ext2 defaults 1 2
> > /dev/hdb8 /usr/src ext2 defaults 1 2
> > /dev/hdb9 swap_upgrade swap defaults 0 0
> > /dev/hdb10 /var ext2 defaults 1 2
> > /dev/hdb11 /tmp ext2 defaults 1 2
> > /dev/hdb12 /opt ext2 defaults 1 2
> > /dev/hdb13 / ext2 defaults 1 1
> > /dev/hdc /mnt/ls120 vfat user,exec,nodev,nosuid,rw,noauto 0 0
> > /dev/sda1 /mnt/DOS_sda1 vfat user,exec,conv=auto 0 0
> > /dev/sda5 /mnt/DOS_sda5 vfat user,exec,conv=auto 0 0
> > /mnt/floppy /mnt/floppy supermount fs=vfat,dev=/dev/fd0 0 0
> > /mnt/cdrom /mnt/cdrom supermount fs=iso9660,dev=/dev/cdrom 0 0
