On Mon, 14 Feb 2000, silkythreads wrote:
> Okay.... The HP7200e may very well be ATAPI but I do not
> currently have IDE-SCSI support installed because it conflicts
> with my SCSI hardware. The HP7200e is connected by parallel port
> to my computer. My primary hard drive and cdrom are SCSI.
> I'm not sure how to configure my conf.module or which device I
> should use to mount the HP7200e on. All attempts to mount only
> effect my primary SCSI cdrom. All the HOWTO's talk about
> scsi-emulation, but they seem to assume you don't have SCSI hardware to
> start with. I do, so the question is,
> How do I get my system to see this drive and my SCSI hardware
> at the same time ???
This is my /etc/conf.modules:
alias scsi_hostadapter aha1542
alias scsi_hostadapter ide-scsi
alias eth0 ne2k-pci
alias parport_lowlevel parport_pc
pre-install plip modprobe parport_pc ; echo 7 > /proc/parport/0/irq
pre-install pcmcia_core CARDMGR_OPTS=-f /etc/rc.d/init.d/pcmcia start
post-install supermount modprobe scsi_hostadapter
alias sound sb
options sb io=0x220 irq=5 dma=1 dma16=5 mpu_io=0x300
This is the pertinant parts of my bootup:
Configuring Adaptec (SCSI-ID 7) at IO:330, IRQ 12, DMA priority 7
aha1542.c: Using extended bios translation
scsi0 : Adaptec 1542
scsi : 1 host.
Vendor: YAMAHA Model: CRW4260 Rev: 1.0q
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 2, lun 0
Vendor: CONNER Model: CP31370 1.3GB3.5 Rev: B0BC
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 3, lun 0
Vendor: IOMEGA Model: ZIP 100 Rev: J.02
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi removable disk sdb at scsi0, channel 0, id 5, lun 0
sr0: scsi3-mmc drive: 6x/6x writer cd/rw xa/form2 cdda tray
SCSI device sda: hdwr sector= 512 bytes. Sectors= 2680258 [1308 MB] [1.3 GB]
sda: sda1
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 196608 [96 MB] [0.1 GB]
sdb: Write Protect is off
sdb: sdb4
scsi1 : SCSI host adapter emulation for IDE ATAPI devices
scsi : 2 hosts.
Vendor: Model: CD-R/RW RW7060A Rev: 1.20
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr1 at scsi1, channel 0, id 0, lun 0
sr1: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
As you can see, it works fine having a real SCSI card in there besides the
emulated IDE-SCSI burner... cdrecord -scanbus gives me this:
Cdrecord release 1.8a29 Copyright (C) 1995-1999 J�rg Schilling
scsibus0:
0,0,0 0) *
0,1,0 1) *
0,2,0 2) 'YAMAHA ' 'CRW4260 ' '1.0q' Removable CD-ROM
0,3,0 3) 'CONNER ' 'CP31370 1.3GB3.5' 'B0BC' Disk
0,4,0 4) *
0,5,0 5) 'IOMEGA ' 'ZIP 100 ' 'J.02' Removable Disk
0,6,0 6) *
0,7,0 7) *
scsibus1:
1,0,0 100) ' ' 'CD-R/RW RW7060A ' '1.20' Removable CD-ROM
1,1,0 101) *
1,2,0 102) *
1,3,0 103) *
1,4,0 104) *
1,5,0 105) *
1,6,0 106) *
1,7,0 107) *
Should work just fine setting up how the HOW-TO's tell you to.
--
Vincent Danen, ICQ: 54924721 . telnet://bbs.freezer-burn.org
BBBS/LiI . Internet Rex for Linux Beta . Freezer Burn BBS
Linux Information and other Goodies at Freezer Burn: www.freezer-burn.org
