Okay.... The HP7200e may very well be ATAPI but I do not currently have IDE-SCSI support installed because it conflicts with my SCSI hardware. The HP7200e is connected by parallel port to my computer. My primary hard drive and cdrom are SCSI. I'm not sure how to configure my conf.module or which device I should use to mount the HP7200e on. All attempts to mount only effect my primary SCSI cdrom. All the HOWTO's talk about scsi-emulation, but they seem to assume you don't have SCSI hardware to start with. I do, so the question is, How do I get my system to see this drive and my SCSI hardware at the same time ??? Audrey Beck wrote: > > You're saying that the HP7299e is connected to your parallel port? When > you are booting, the scsi controller doesn't show that there is a second > cd rom drive. How does it become scsi connected to the parallel port? > > silkythreads wrote: > > > > Mike, > > I do not own an IDE/ATAPI CDROM. > > Half of my hardware is SCSI > > > > My conf.module looks like this: > > > > alias scsi_hostadapter aic7xxx > > alias eth0 tulip > > alias eth1 tulip > > alias parport_lowlevel parport_pc > > alias sound es1371 > > > > pre-install pcmcia_core /etc/rc.d/init.d/pcmcia start > > pre-install plip modprobe parport_pc ; echo 7 > /proc/parport/0/irq > > post-install supermount modprobe scsi_hostadapter > > > > I'm wondering if I should add something like this, change line 1 to: > > alias scsi_hostadapter aic7xxx, ide-scsi > > > > But, I just don't know. > > > > Mike Hahn wrote: > > > > > First, is it ATAPI? If so you may want to try these changes in your kernel > > > configuration: > > > Under Block Devices: > > > 1) turning off IDE/ATAPI CDROM support > > > 2) enable SCSI emulation support > > > Under SCSI support > > > 1) enable SCSI CD-ROM support > > > 2) enable SCSI generic support > > > > > > Then recompile and install the new kernel. I had the same problem > > > although my cdrom is internal, I read somewhere that if your kernel sees > > > an ATAPI cdrom it will load it first and disregard SCSI support. Also > > > make sure you have the line: > > > > > > append = "hd?=ide-scsi" > > > > > > in your lilo.conf file . Obviously replace the ? with the logical drive. > > > > > > Hope this helps > > > > > > Mike Hahn > > > > > > silkythreads wrote: > > > > > > > I have MANDRAKE 7.0, Kernel 2.2.14-15mdk installed. > > > > > > > > Everything works EXCEPT .......my HP 7200e (that;'s external) > > > > > > > > I've tried it, it does not work. Only my scsi cdrom responds. > > > > > > > > Here's my story ...... > > > > > > > > Internal hardware: > > > > > > > > hda: Maxtor 91360D9, ATA DISK drive > > > > hdb: WDC AC33100H, ATA DISK drive > > > > hdc: LS-120 CSMO 05 UHD Floppy, ATAPI FLOPPY drive > > > > > > > > I have internal SCSI installed > > > > > > > > scsi id 5 PLEXTOR CD-ROM PX-32TS - This is my primary CDROM > > > > scsi id 6 IBM DCAS-34330W - This is my primary HARDDRIVE (2 parts - > > > > > > > > sda1, sda5) > > > > > > > > parport is installed. I have an external HP 694C printer on the end of > > > > my > > > > parallel port chain. > > > > > > > > My HP 7200e is in between the computer and printer. > > > > > > > > I can not get my computer to recognize my cdrw. > > > > > > > > I've tried "mount -t iso9660 /dev/scd0 /mnt/cdrw" > > > > And it only re-mounts my primary cdrom, which of course is now mounted > > > > twice. > > > > (Actually, I tried everything I've read and more than I wanted too.) > > > > > > > > I keep thinking that if the CDRW requires ide-scsi support, I should try > > > > > > > > and make my scsi adapter see it, to define an ID for it. > > > > > > > > HELP !! I CAN NOT GET THIS TO WORK, and I'll bet it's something > > > > SO SIMPLY !! > > > > > > > > Included with this request for HELP is a copy of my dmesg and fstab > > > > file. > > > > > > > > Thanks for creative suggestions. > > > > > > > > BTY - I've read all the documentation and ton's of newsgroup postings, > > > > NOTHING has helped so far. > > > > > > > > *********************************************************************** > > > > dmesg output > > > > *********************************************************************** > > > > Linux version 2.2.14-15mdk ([EMAIL PROTECTED]) (gcc version > > > > 2.95.2 19991024 (release)) #1 Tue Jan 4 22:24:20 CET 2000 > > > > relocating initrd image: > > > > initrd_start:0xc0fa5000 initrd_end:0xc0fff270 > > > > mem_start:0xc026d000 mem_end:0xcfff0000 > > > > initrd_size:0x0005a270 dest:0xcff95000 > > > > Detected 348489026 Hz processor. > > > > Console: colour VGA+ 80x25 > > > > Calibrating delay loop... 347.34 BogoMIPS > > > > Memory: 257252k/262080k available (1092k kernel code, 416k reserved, > > > > 2892k data, 64k init, 0k bigmem) > > > > Dentry hash table entries: 262144 (order 9, 2048k) > > > > Buffer cache hash table entries: 262144 (order 8, 1024k) > > > > Page cache hash table entries: 65536 (order 6, 256k) > > > > VFS: Diskquotas version dquot_6.4.0 initialized > > > > CPU: Intel Pentium II (Deschutes) stepping 01 > > > > Checking 386/387 coupling... OK, FPU using exception 16 error reporting. > > > > > > > > Checking 'hlt' instruction... OK. > > > > POSIX conformance testing by UNIFIX > > > > mtrr: v1.35a (19990819) Richard Gooch ([EMAIL PROTECTED]) > > > > PCI: PCI BIOS revision 2.10 entry at 0xfd993 > > > > PCI: Using configuration type 1 > > > > PCI: Probing PCI hardware > > > > PCI: Enabling I/O for device 00:60 > > > > PCI: Enabling I/O for device 00:70 > > > > PCI: Enabling memory for device 00:70 > > > > PCI: Enabling I/O for device 00:78 > > > > PCI: Enabling memory for device 00:78 > > > > Linux NET4.0 for Linux 2.2 > > > > Based upon Swansea University Computer Society NET3.039 > > > > NET4: Unix domain sockets 1.0 for Linux NET4.0. > > > > NET4: Linux TCP/IP 1.0 for NET4.0 > > > > IP Protocols: ICMP, UDP, TCP, IGMP > > > > TCP: Hash tables configured (ehash 262144 bhash 65536) > > > > Initializing RT netlink socket > > > > Starting kswapd v 1.5 > > > > Detected PS/2 Mouse Port. > > > > Serial driver version 4.27 with MANY_PORTS MULTIPORT SHARE_IRQ enabled > > > > ttyS00 at 0x03f8 (irq = 4) is a 16550A > > > > pty: 256 Unix98 ptys configured > > > > apm: BIOS version 1.2 Flags 0x03 (Driver version 1.9) > > > > Real Time Clock Driver v1.09 > > > > RAM disk driver initialized: 16 RAM disks of 4096K size > > > > PIIX4: IDE controller on PCI bus 00 dev 39 > > > > PIIX4: not 100% native mode: will probe irqs later > > > > ide0: BM-DMA at 0x1000-0x1007, BIOS settings: hda:DMA, hdb:pio > > > > ide1: BM-DMA at 0x1008-0x100f, BIOS settings: hdc:pio, hdd:pio > > > > hd0: C/H/S=27625/247/228 from BIOS ignored > > > > hda: Maxtor 91360D8, ATA DISK drive > > > > hdb: WDC AC33100H, ATA DISK drive > > > > hdc: LS-120 CSMO 05 UHD Floppy, ATAPI FLOPPY drive > > > > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > > > > ide1 at 0x170-0x177,0x376 on irq 15 > > > > hda: Maxtor 91360D8, 12970MB w/256kB Cache, CHS=26353/16/63 > > > > hdb: WDC AC33100H, 3020MB w/128kB Cache, CHS=1024/255/63 > > > > Floppy drive(s): fd0 is 1.44M > > > > FDC 0 is a post-1991 82077 > > > > md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12 > > > > raid5: measuring checksumming speed > > > > raid5: MMX detected, trying high-speed MMX checksum routines > > > > pII_mmx : 768.477 MB/sec > > > > p5_mmx : 803.910 MB/sec > > > > 8regs : 622.935 MB/sec > > > > 32regs : 328.041 MB/sec > > > > using fastest function: p5_mmx (803.910 MB/sec) > > > > scsi : 0 hosts. > > > > scsi : detected total. > > > > md.c: sizeof(mdp_super_t) = 4096 > > > > Partition check: > > > > hda: [PTBL] [1653/255/63] hda1 hda2 < hda5 hda6 hda7 hda8 hda9 > > > > > hdb: hdb1 hdb2 < hdb5 hdb6 hdb7 hdb8 hdb9 hdb10 hdb11 hdb12 hdb13 > > > > > RAMDISK: Compressed image found at block 0 > > > > autodetecting RAID arrays > > > > autorun ... > > > > ... autorun DONE. > > > > VFS: Mounted root (ext2 filesystem). > > > > (scsi0) <Adaptec AHA-294X Ultra SCSI host adapter> found at PCI 13/0 > > > > (scsi0) Wide Channel, SCSI ID=7, 16/255 SCBs > > > > (scsi0) Warning - detected auto-termination > > > > (scsi0) Please verify driver detected settings are correct. > > > > (scsi0) If not, then please properly set the device termination > > > > (scsi0) in the Adaptec SCSI BIOS by hitting CTRL-A when prompted > > > > (scsi0) during machine bootup. > > > > (scsi0) Cables present (Int-50 YES, Int-68 YES, Ext-68 NO) > > > > (scsi0) Downloading sequencer code... 413 instructions downloaded > > > > scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.21/3.2.4 > > > > <Adaptec AHA-294X Ultra SCSI host adapter> > > > > scsi : 1 host. > > > > (scsi0:0:5:0) Synchronous at 20.0 Mbyte/sec, offset 15. > > > > Vendor: PLEXTOR Model: CD-ROM PX-32TS Rev: 1.02 > > > > Type: CD-ROM ANSI SCSI revision: 02 > > > > Detected scsi CD-ROM sr0 at scsi0, channel 0, id 5, lun 0 > > > > (scsi0:0:6:0) Synchronous at 40.0 Mbyte/sec, offset 8. > > > > Vendor: IBM Model: DCAS-34330W Rev: S65A > > > > Type: Direct-Access ANSI SCSI revision: 02 > > > > Detected scsi disk sda at scsi0, channel 0, id 6, lun 0 > > > > Uniform CDROM driver Revision: 2.56 > > > > SCSI device sda: hdwr sector= 512 bytes. Sectors= 8467200 [4134 MB] [4.1 > > > > GB] > > > > sda: sda1 sda2 < sda5 > > > > > tulip.c:v0.91g-ppc 7/16/99 [EMAIL PROTECTED] > > > > eth0: Lite-On 82c168 PNIC rev 32 at 0x1800, 00:A0:CC:57:0D:AD, IRQ 11. > > > > eth0: MII transceiver #1 config 3000 status 7829 advertising 01e1. > > > > eth1: Lite-On 82c168 PNIC rev 33 at 0x2000, 00:A0:CC:3E:24:6F, IRQ 10. > > > > eth1: MII transceiver #1 config 1000 status 782d advertising 01e1. > > > > autodetecting RAID arrays > > > > autorun ... > > > > ... autorun DONE. > > > > VFS: Mounted root (ext2 filesystem) readonly. > > > > change_root: old root has d_count=1 > > > > Trying to unmount old root ... okay > > > > Freeing unused kernel memory: 64k freed > > > > Adding Swap: 133016k swap-space (priority -1) > > > > es1371: version v0.19 time 22:34:23 Jan 4 2000 > > > > es1371: found adapter at io 0x1040 irq 11 > > > > es1371: features: joystick 0x0 > > > > es1371: codec vendor CRY revision 3 > > > > es1371: codec features Headphone out 18bit DAC 18bit ADC > > > > es1371: stereo enhancement: no 3D stereo enhancement > > > > cdrom: open failed. > > > > VFS: Disk change detected on device sr(11,0) > > > > VFS: Disk change detected on device fd(2,0) > > > > [MS-DOS FS Rel. 12,FAT 0,check=n,conv=b,uid=0,gid=0,umask=022,bmap] > > > > >[me=0xfe,cs=0,#f=0,fs=1810,fl=144680,ds=1810,de=0,data=1810,se=28672,ts=940114177,ls=5120,rc=0,fc=4294967295] > > > > > > > > Transaction block size = 512 > > > > VFS: Can't find a valid MSDOS filesystem on dev 02:00. > > > > parport0: PC-style at 0x378 [SPP,PS2,EPP] > > > > parport0: Printer, HEWLETT-PACKARD DESKJET 690C > > > > lp0: using parport0 (polling). > > > > > > > > *********************************************************************** > > > > FSTAB file > > > > *********************************************************************** > > > > > > > > none /proc proc defaults 0 0 > > > > none /dev/pts devpts mode=0620 0 0 > > > > /dev/hda1 /mnt/DOS_hda1 vfat user,exec,conv=auto 0 0 > > > > /dev/hda5 /mnt/DOS_hda5 vfat user,exec,conv=auto 0 0 > > > > /dev/hda6 /mnt/DOS_hda6 vfat user,exec,conv=auto 0 0 > > > > /dev/hda7 /mnt/DOS_hda7 vfat user,exec,conv=auto 0 0 > > > > /dev/hda8 /mnt/DOS_hda8 vfat user,exec,conv=auto 0 0 > > > > /dev/hda9 /mnt/DOS_hda9 vfat user,exec,conv=auto 0 0 > > > > /dev/hdb1 /boot ext2 defaults 1 2 > > > > /dev/hdb5 /usr ext2 defaults 1 2 > > > > /dev/hdb6 /usr/local ext2 defaults 1 2 > > > > /dev/hdb7 /home ext2 defaults 1 2 > > > > /dev/hdb8 /usr/src ext2 defaults 1 2 > > > > /dev/hdb9 swap_upgrade swap defaults 0 0 > > > > /dev/hdb10 /var ext2 defaults 1 2 > > > > /dev/hdb11 /tmp ext2 defaults 1 2 > > > > /dev/hdb12 /opt ext2 defaults 1 2 > > > > /dev/hdb13 / ext2 defaults 1 1 > > > > /dev/hdc /mnt/ls120 vfat user,exec,nodev,nosuid,rw,noauto 0 0 > > > > /dev/sda1 /mnt/DOS_sda1 vfat user,exec,conv=auto 0 0 > > > > /dev/sda5 /mnt/DOS_sda5 vfat user,exec,conv=auto 0 0 > > > > /mnt/floppy /mnt/floppy supermount fs=vfat,dev=/dev/fd0 0 0 > > > > /mnt/cdrom /mnt/cdrom supermount fs=iso9660,dev=/dev/cdrom 0 0
begin:vcard n:Williams;Donna tel;home:301-310-0441 tel;work:301-310-0441 x-mozilla-html:FALSE org:General Dynamics - Electronic Systems;GD - ES adr:;;;;;; version:2.1 email;internet:[EMAIL PROTECTED] title:Software Test Engineer fn:Donna Williams end:vcard
