John, Sounds like you might need to do a RX image calibration.
What radio are you using? -Tim -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of John Lennerton Sent: Friday, February 18, 2011 11:49 PM To: Bret Mills Cc: [email protected] Subject: Re: [FlexEdge] 2.0.19 RC1 showing odd behavior Bret, Power reset didn't do it for me, and I've uninstalled and re-installed 2.0.19. Same result. Thanks for the suggestion, though. As I'm running Windows 7, I had to hunt down all the settings files, and I think I got them all, but maybe I'm not getting everything. I noticed a RX calibration cycle on the first install, but the re-install didn't do that; it did fft optimization, backed up the EEPROM and retrieved the calibration data from EEPROM. Is there a way to force a complete re-install? On Fri, Feb 18, 2011 at 11:42 PM, Bret Mills <[email protected]> wrote: > My radio did this and I was hearing WWV on 40 meters in about 20 > places, I did a Power Reset and it came back to normal, except MY TX > goes away ever so often and takes another Radio Power reset. Be sure > to close PowerSDR before you do a power reset on the radio. > Hope this helps > Bret > WX7Y > > > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of John Lennerton > Sent: Friday, February 18, 2011 9:17 PM > To: [email protected] > Subject: [FlexEdge] 2.0.19 RC1 showing odd behavior > > OK, so this is probably something I've done incorrectly, as everyone > else seems to be having zero issues, but.... > > Installed 2.0.19 with no problems. I didn't remove 2.0.16. Started > up the new software, it went through it's stuff, did a RX calibration, etc. > > Started PSDR, and all seemed normal. So far, so good. > > On 40M, at 7.028 MHz, not too much going on above that frequency on > the panadapter display, but I'm hearing stuff on that freq and see > activity below. > > Tune up to 7.029 MHz, and all kinds of signals jump out of nowhere, > the band is crazy, and I remember it's a contest weekend. But wait; > why didn't I see all this activity 1 KHz ago? It's repeatable, and I > have screen shots. > > Also, the noise floor seems to be 10 - 20 db higher. > > Not a huge problem, as I can revert to 2.0.16 and all is well. > > Any ideas? > > -- > Regards and 73, > > John Lennerton, W1JCL > _______________________________________________ > Flexedge mailing list > [email protected] > http://mail.flex-radio.biz/mailman/listinfo/flexedge_flex-radio.biz > This is the FlexRadio Systems e-mail Reflector called FlexEdge. It is > used for posting topics related to SDR software development and > experimentalist who are using beta versions of the software. > > -- > This message has been scanned for viruses and dangerous content by > MailScanner, and is believed to be clean. > > > -- > This message has been scanned for viruses and dangerous content by > MailScanner, and is believed to be clean. > > -- Regards, John Lennerton, W1JCL _______________________________________________ Flexedge mailing list [email protected] http://mail.flex-radio.biz/mailman/listinfo/flexedge_flex-radio.biz This is the FlexRadio Systems e-mail Reflector called FlexEdge. It is used for posting topics related to SDR software development and experimentalist who are using beta versions of the software. _______________________________________________ Flexedge mailing list [email protected] http://mail.flex-radio.biz/mailman/listinfo/flexedge_flex-radio.biz This is the FlexRadio Systems e-mail Reflector called FlexEdge. It is used for posting topics related to SDR software development and experimentalist who are using beta versions of the software.
