Warner Losh wrote:
> In message <[EMAIL PROTECTED]> Marcel Moolenaar writes:
> : The ability to do cross builds rules out the need to update binutils
> : first. I haven't done any cross-builds since, well, februari, so I'm not
> : at all up to date on that front; things may have been broken by then...
> I did a complete buildworld in early May w/o a hitch that worked when
> I installed it on my bouncer box.
> Maybe I just need more swap than I have on my machine, or higher
> limits for the process building things.  Then again, I do have 1/2G of
> swap that isn't being used at all during the builds...


I've got 500MB of swap.  It is never touched during
the build.  The machine is very lightly loaded (i.e.,
only "make buildworld" running).

I was surprise that no one else had reported this problem
when I sent my original e-mail.  It must be restricted to 
a specific hardware combination.


Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1982, 1986, 1989, 1991, 1993
        The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #0: Fri May 26 09:39:34 PDT 2000
    [EMAIL PROTECTED]:/usr/src/sys/compile/TROUTMASK
Timecounter "i8254"  frequency 1193182 Hz
CPU: Pentium Pro (199.31-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x619  Stepping = 9
real memory  = 268435456 (262144K bytes)
avail memory = 257748992 (251708K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor motherboard
 cpu0 (BSP): apic id:  1, version: 0x00040011, at 0xfee00000
 cpu1 (AP):  apic id:  0, version: 0x00040011, at 0xfee00000
 io0 (APIC): apic id:  2, version: 0x00170011, at 0xfec00000
Preloaded elf kernel "kernel" at 0xc0346000.
VESA: v1.2, 4096k memory, flags:0x0, mode table:0xc00c1bdf (c0001bdf)
VESA: S3 Incorporated. 86C325
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
isab0: <Intel 82371SB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
pci0: <Intel PIIX3 ATA controller> at 7.1
pci0: <S3 ViRGE graphics accelerator> at 15.0 irq 19
ahc0: <Adaptec 2940 Ultra SCSI adapter> port 0xf400-0xf4ff mem 0xf0dff000-0xf0dfffff 
irq 18 at device 16.0 on pci0
ahc0: aic7880 Single Channel A, SCSI Id=7, 16/255 SCBs
xl0: <3Com 3c905-TX Fast Etherlink XL> port 0xf0c0-0xf0ff irq 17 at device 17.0 on pci0
xl0: Ethernet address: 00:60:97:98:38:65
miibus0: <MII bus> on xl0
nsphy0: <DP83840 10/100 media interface> on miibus0
nsphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> on isa0
sc0: VGA <8 virtual consoles, flags=0x200>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: This ppc chipset does not support the extended I/O port range...no problem
ppc0: <Parallel port> at port 0x378-0x37b irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
pps0: <Pulse per second Timing Interface> on ppbus0
ppi0: <Parallel I/O> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
unknown0: <PNP0a03> at port 0xcf8-0xcff on isa0
unknown: <PNP0501> can't assign resources
unknown: <PNP0501> can't assign resources
unknown: <PNP0400> can't assign resources
unknown: <PNP0700> can't assign resources
unknown1: <PNP0c02> at port 
iomem 0xfff80000-0xffffffff on isa0
unknown2: <PNP0c01> at iomem 0-0x9ffff,0xe0000-0xfffff,0x100000-0xfffffff on isa0
unknown3: <PNP0200> at port 0-0xf,0x81-0x8f,0xc0-0xdf drq 4 on isa0
unknown4: <PNP0000> at port 0x20-0x21,0xa0-0xa1 irq 2 on isa0
unknown5: <PNP0100> at port 0x40-0x43 irq 0 on isa0
unknown6: <PNP0b00> at port 0x70-0x71 irq 8 on isa0
unknown: <PNP0303> can't assign resources
npxisa0: <Legacy ISA coprocessor support> at port 0xf0-0xff irq 13 on isa0
unknown7: <PNP0800> at port 0x61 on isa0
unknown: <PNP0f13> can't assign resources
unknown8: <PNP0c02> at port 0x4d0-0x4d1 on isa0
unknown9: <PNP0c02> at iomem 0xfec00000-0xfec0ffff,0xfee00000-0xfee00fff on isa0
unknown10: <WaveTable> at port 0x620-0x623 on isa0
sbc0: <Creative SB16/SB32> at port 0x220-0x22f,0x330-0x331,0x388-0x38b irq 5 drq 1,5 
on isa0
sbc0: setting card to irq 5, drq 1, 5
pcm0: <SB DSP 4.13> on sbc0
unknown11: <Game> at port 0x200-0x207 on isa0
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
Waiting 10 seconds for SCSI devices to settle
SMP: AP CPU #1 Launched!
sa0 at ahc0 bus 0 target 1 lun 0
sa0: <DEC DLT2000 8B37> Removable Sequential Access SCSI-2 device 
sa0: 5.000MB/s transfers (5.000MHz, offset 15)
cd0 at ahc0 bus 0 target 6 lun 0
cd0: <PLEXTOR CD-ROM PX-12CS 1.00> Removable CD-ROM SCSI-2 device 
cd0: 10.000MB/s transfers (10.000MHz, offset 15)
cd0: cd present [312700 x 2048 byte records]
da1 at ahc0 bus 0 target 3 lun 0
da1: <QUANTUM LIGHTNING 730S 241E> Fixed Direct Access SCSI-2 device 
da1: 5.000MB/s transfers (5.000MHz, offset 8)
da1: 699MB (1431760 512 byte sectors: 64H 32S/T 699C)
da0 at ahc0 bus 0 target 0 lun 0
da0: <SEAGATE ST34371N 0280> Fixed Direct Access SCSI-2 device 
da0: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled
da0: 4148MB (8496960 512 byte sectors: 255H 63S/T 528C)
Mounting root from ufs:/dev/da0s1a
pid 1982 (ld), uid 0: exited on signal 10 (core dumped)
pid 24991 (ld), uid 0: exited on signal 10 (core dumped)
pid 51517 (ld), uid 0: exited on signal 10 (core dumped)
pid 77559 (ld), uid 0: exited on signal 10 (core dumped)
pid 56815 (ld), uid 0: exited on signal 10 (core dumped)

To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-current" in the body of the message

Reply via email to