On Sun, Oct 1, 2017 at 7:21 PM, Hans Petter Selasky <h...@selasky.org> wrote: > On 10/01/17 19:09, Tomasz CEDRO wrote: >> >> On Sun, Oct 1, 2017 at 6:40 PM, Ian Lepore <i...@freebsd.org> wrote: >>> >>> On Sun, 2017-10-01 at 18:33 +0200, Tomasz CEDRO wrote: >>>> >>>> On Wed, Sep 27, 2017 at 8:32 AM, Hans Petter Selasky <h...@selasky.org >>>>> >>>>> wrote: >>>>> >>>>> On 09/27/17 00:37, Ian Lepore wrote: >>>>>> >>>>>> >>>>>> >>>>>> On Wed, 2017-09-27 at 00:30 +0200, Hans Petter Selasky wrote: >>>>>>> >>>>>>> >>>>>>> >>>>>>> On 09/27/17 00:11, Tomasz CEDRO wrote: >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>>> https://github.com/freebsd/freebsd/pull/115 >>>>>>>> >>>>>>>> :-) >>>>>>>> >>>>>>> The devd.conf rule should match more than just vendor and >>>>>>> product: >>>>>>> >>>>>>> >>>>>>> +# Load GOBI 2000/3000 U3G QDL modem firmware on attach / boot. >>>>>>> +# Note: This requires additional "gobi_loader" utility to be >>>>>>> installed, >>>>>>> +# as well as valid QDL driver firmware files placed in >>>>>>> /boot/firmware/gobi. >>>>>>> +# If modem does not accept valid firmware try gobi_loader >>>>>>> -2000 >>>>>>> switch. >>>>>>> +# Please adjust modem VID/PID to match your device supported >>>>>>> by >>>>>>> u3g >>>>>>> module. >>>>>>> +#attach 100 { >>>>>>> +# match "vendor" "0x04da"; >>>>>>> +# match "product" "0x250e"; >>>>>>> +# action "/usr/local/sbin/gobi_loader /dev/cuaU0 >>>>>>> /boot/firmware/gobi/"; >>>>>>> +#}; >>>>>>> >>>>>>> Else patch looks good. >>>>>>> >>>>>>> --HPS >>>>>> >>>>>> >>>>>> Hard-coding /dev/cuaU0 cannot possibly be right. >>>>>> >>>>>> -- Ian >>>>>> >>>>> These three lines are missing: >>>>> >>>>> match "system" "DEVFS"; >>>>> match "subsystem" "CDEV"; >>>>> match "type" "CREATE"; >>>>> >>>>> >>>>> --HPS >>>> >>>> Thanks! Updated! :-) >>>> >>>> https://github.com/freebsd/freebsd/pull/115 >>>> >>> >>> If this is to be an example, it should be correct. Please replace the >>> "cuaU0" with "$cdev". (See /etc/devd/uath.conf for an example). >>> >>> -- Ian >> >> >> Thanks Ian! Is it okay now? I have moved this example to dedicated >> /etc/devd/u3g.conf file, and added u3g load to /etc/devd/usb.conf.. if >> syntax is okay I will verify on my laptop.. >> >> https://github.com/freebsd/freebsd/pull/115 >> > > Looks good to me. Don't forget to MFC! > > --HPS
/etc/devd/u3g.conf: notify 100 { match "system" "USB"; match "subsystem" "DEVICE"; match "type" "ATTACH"; match "vendor" "0x04da"; match "product" "0x250e"; action "/usr/local/bin/gobi_loader /dev/$cdev /boot/firmware/gobi/"; }; This does not work when /dev/$cdev is used.. but it works when /dev/cuaU0 is used. Ian, could you please advise? :-) -- CeDeROM, SQ7MHZ, http://www.tomek.cedro.info _______________________________________________ freebsd-usb@freebsd.org mailing list https://lists.freebsd.org/mailman/listinfo/freebsd-usb To unsubscribe, send any mail to "freebsd-usb-unsubscr...@freebsd.org"