Your new NIC has an IP of 127.0.0.1 ? That's the loopback address. You
don't assign a hardware NIC to the loopback. Pick something else.
--
Aaron Turner [EMAIL PROTECTED] 650.237.0300 x252
Security Engineer Vicinity Corp.
Cell: 408-314-9874 http://www.vicinity.com
On Fri, 2 Jun 2000, davidxs wrote:
>
> Hello All,
>
> Thanks for all of the replies regarding adding additional NICs to a FW box.
> Unfortantly I haven't been able to get it to work yet... The new interface
> fails to show up in "route print" in NT meaning NT isn't recognizing the new
> NIC. (interface IP (new NIC) 127.0.0.1)
>
> All NICs have seperate subnets assigned to them so I know that isn't a
> problem, and traffic flows normally through the other main internal and
> external NICs just fine. I was hoping that adding the NIC wouldn't be as
> intrusive as reinstalling FW-1, but it looks like that is the course to
> take...
>
> What eddy lists below in backing up directories... Is that all?? I have seen
> other posts saying to back up more... Is there anything in a directory, when
> put back after reinstall that would effect the new install negatively in the
> sense that a new NIC is now in place...The posts below states that all *.W,
> *.pf, *.C, and rulebases.fws should be copied and the same SP be in place
> when building a new firewall with the same rules, etc...
>
> Is there any real difference between building a new firewall to take
> another's configuration and re-installing fw-1 on a box after adding a new
> NIC in terms of what is need to be copied in the fw directory after install?
>
> David
>
>
>
> Previous Posts on FW migrations ---------------------------
>
>
> Make sure the FW's are at the same level and the same SP before you try this
> or you'll have issues.
>
> Mike
>
> > -----Original Message-----
> > From: James Otts [SMTP:[EMAIL PROTECTED]]
> > Sent: a iae 30 2000 23:35
> > To: Troy Fontenot
> > Cc: [EMAIL PROTECTED]
> > Subject: RE: [FW1] Copying a rule base from one firewall to another
> >
> >
> > Yup... I believe you just need *.W, *.pf, *.C, and rulebases.fws
> >
> > James
> >
> > > -----Original Message-----
> > > From: Troy Fontenot [mailto:[EMAIL PROTECTED]]
> > > Sent: Tuesday, May 30, 2000 4:31 PM
> > > To: [EMAIL PROTECTED]
> > > Subject: [FW1] Copying a rule base from one firewall to another
> > >
> > > Is it possible to copy a rule base and the objects from one firewall to
> > > another if they are both running at the same version and service pack
> > > level? If so, which files do I need to copy?
> > >
> > >
> > > Troy Fontenot
>
>
>
> -----Original Message-----
> From: [EMAIL PROTECTED]
> [mailto:[EMAIL PROTECTED]]On Behalf Of Eddy
> Chien
> Sent: Thursday, June 01, 2000 1:12 PM
> To: [EMAIL PROTECTED]
> Cc: [EMAIL PROTECTED]
> Subject: RE: [FW1] FW: 3rd NIC card problem
>
>
>
> Hi Sunny,
>
> Did you re-install FW-1 after adding the new network card? Because FW-1
> needs to put inspect module between protocol stack and NIC driver. You will
> need to re-install FW-1 after making any changes to the network card.
>
> The proper procedure for adding / removing network card or even applying
> service pack is:
> 1. Backup your fw configuration: basically the winnt\fw\conf and
> winnt\fw\state directories.
> 2. Make what ever changes you need.
> 3. Re-install Fw-1.
> 4. Copy the two directories mentioned above back.
>
>
> Hope this helps
>
>
>
> eddy chien
>
>
> >From: Sunny Kwan <[EMAIL PROTECTED]>
> >To: [EMAIL PROTECTED]
> >CC: [EMAIL PROTECTED]
> >Subject: RE: [FW1] FW: 3rd NIC card problem
> >Date: Thu, 1 Jun 2000 19:26:40 +0800
> >
> >No, I don't mean that. What I mean is: there should be only one default
> >gateway for the NT server itself. Take for example:
> >NIC 1 - ip 10.1.1.1 mask 255.255.255.0 (no default gateway)
> >NIC 2 - ip 192.168.1.1 mask 255.255.255.0 (no default gateway)
> >NIC 3 - ip 207.133.4.50 mask 255.255.255.0 default gateway 207.133.4.254
> >(your router)
> >So the whole server have only one default gateway then it can find way out.
> >
> >Sunny Kwan
> >Infrastructure Manager, renren.com
> >Home for the global Chinese family -
> >http://www.renren.com <http://www.renren.com/>
> >
> >-----Original Message-----
> >From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]
> >Sent: Thursday, June 01, 2000 7:08 PM
> >To: Sunny Kwan
> >Subject: RE: [FW1] FW: 3rd NIC card problem
> >
> >
> >Let me see if I understand this: the new NIC has an address on the same
> >subnet as one of the existing cards? If so - how do you expect NT to make
> >routing decisions to use the card? To my knowledge, it is impossible for
> >NT
> >to act as a bridge.
> >
> > -----Original Message-----
> >From: davidxs [mailto:[EMAIL PROTECTED]]
> >Sent: Thursday, June 01, 2000 12:06 AM
> >To: Fw-1-Mailinglist
> >Subject: [FW1] FW: 3rd NIC card problem
> >
> >
> >Hello All,
> >
> >I am trying to put a 3rd NIC into my FW 4.0 without success. After
> >installing the driver for the NIC sucessfully for NT, the FW will not allow
> >traffic through its external interface. I have tried adding the the new
> >interface to the FW object without sucess as well. The new card has an IP
> >address of the the same class C internally but obviously a different
> >specific IP from other the internal NIC.
>
> ________________________________________________________________________
> Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com
>
>
>
> ============================================================================
> ====
> To unsubscribe from this mailing list, please see the instructions at
> http://www.checkpoint.com/services/mailing.html
> ============================================================================
> ====
>
>
>
> ================================================================================
> To unsubscribe from this mailing list, please see the instructions at
> http://www.checkpoint.com/services/mailing.html
> ================================================================================
>
================================================================================
To unsubscribe from this mailing list, please see the instructions at
http://www.checkpoint.com/services/mailing.html
================================================================================
