If it pops up and you don’t take any action to save then all those transactions accumulated since last save will stay pending to be saved; you’ll have to click on File à Save to persist them on to the disk at your choosing. This would be also the case for when it is shutting down because the shutdown process will kill the process without saving. If you are automagically looking for the system to press yes for that prompt when you asked for it to prompt you then it is not going to do it for you. That dialogue is for you to take the action; not for the system.
Understand the ramifications of not setting up to automatically save and have it prompt to you for saving it very thoroughly. While option is there to prompt for save, it makes little sense in normal use case by a laymen to not automatically save all the time at certain interval rather than prompt for it. Knowing how GNC behaves, when you said “One of the options was to save this time, one was to sautomagically save all the time without asking, etc. I still have it pop up.” that is likely that the setting you select during that pop up it is only good going forward for that session of the GNC run and not saved persistently to the disk. Once you exit and relaunch, it will re-read setting from the disk and return back to prompting unless you go into Edit à Preferences à General and setup auto-save settings. If you uncheck ‘Show auto-save confirmation question’ in there, it will always save at that interval without prompting (auto save does *not* overwrite existing file; it creates a new file with a timestamp in the name of the file). Right underneath is also setting to timeout display of that “save now” pop-up so if you do not act within that allotted prompt time and system ends up dismissing it due to time out then it won’t save and all changes accumulated since last save will be pending to be saved as well. HTH. From: Clint Chaplin <[email protected]> Sent: Friday, October 02, 2026 8:05 PM To: Kalpesh Patel <[email protected]> Cc: scum buster <[email protected]>; Robert Heller <[email protected]>; David T. <[email protected]>; [email protected] Subject: Re: [GNC] Autosave question One other possibility; the default setup on my windows installation was to pop up a window when autosave was triggered to ask the user what to do. One of the options was to save this time, one was to sautomagically save all the time without asking, etc. I still have it pop up. If that option is enabled, what happens when shut down? On Fri, Oct 2, 2026 at 4:56 PM Kalpesh Patel <[email protected] <mailto:[email protected]> > wrote: That sounds like your backend storage might be the cloud storage or you have very old drive that is not flushing cache before powering down. Assuming it is Intel pc, make sure BIOS settings for hard drive is set to AHCI mode and set it as removable or hot swappable drive type which should force it to flush cache upon power down command is sent to it. ----- Excuse the typos. It's the mobile thingy! On October 2, 2026 6:59:05 PM scum buster <[email protected] <mailto:[email protected]> > wrote: > > I have it set to autosave and apparantly it ISNT autosaving.....its not > just one transaction that gets lost...its a bunch, which were done > during my last session (if I did not manually save it). > > On 10/1/2026 5:56 PM, Kalpesh Patel wrote: >> I have the pre-build binaries of the 4.14 version running on Windows and it >> auto saves as well. If anything it would only be the current in-flight >> transaction not saved. >> >> -----Original Message----- >> From: Robert Heller <[email protected] <mailto:[email protected]> > >> Sent: Thursday, October 01, 2026 2:29 PM >> To: David T. <[email protected] <mailto:[email protected]> > >> Cc: [email protected] <mailto:[email protected]> ; David >> Carlson <[email protected] <mailto:[email protected]> >; >> ? >> scum buster <[email protected] <mailto:[email protected]> > >> Subject: Re: [GNC] Autosave question >> >> I'm still using a built-from-source 4.14, and the auto-save does in fact >> save the file. >> >> At Thu, 01 Oct 2026 21:42:17 +0530 "David T." <[email protected] >> <mailto:[email protected]> > wrote: >> >>> I don't use this feature, but the documentation very clearly states: >>> >>> "Auto-save time interval: This field sets the number of minutes between >> each automatic saving of the file. Set to 0 to disable the auto-save >> feature." >>> This (and the name of the preference) would strongly suggest that the >> feature is supposed to, ahem, *save* the file in question, and not just toss >> up a reminder. >>> But, I'm sure I've misread things. >>> >>> David T. >>> >>> On October 1, 2026 8:50:27 PM GMT+05:30, David Carlson >> <[email protected] <mailto:[email protected]> > wrote: >>>> iirc, auto save is only a reminder, not an action. However, you >>>> should be able to import transactions entered after the last manual >>>> save using the replay logs feature. >>>> >>>> On Thu, Oct 1, 2026 at 7:56C"B > > -- > This email has been checked for viruses by Avast antivirus software. > www.avast.com <http://www.avast.com> _______________________________________________ gnucash-user mailing list [email protected] <mailto:[email protected]> To update your subscription preferences or to unsubscribe: https://lists.gnucash.org/mailman/listinfo/gnucash-user ----- Please remember to CC this list on all your replies. You can do this by using Reply-To-List or Reply-All. -- Clint (JOATMON) Chaplin _______________________________________________ gnucash-user mailing list [email protected] To update your subscription preferences or to unsubscribe: https://lists.gnucash.org/mailman/listinfo/gnucash-user ----- Please remember to CC this list on all your replies. You can do this by using Reply-To-List or Reply-All.
