I did 60 degrees everywhere ie beveled top of the walls in as well. Foam does not like being cut at sharp angles, so 30 degree may not come out well... On Jun 17, 2014 8:23 AM, "Tiprin Lujan" <[email protected]> wrote:
> Great! Thanks for the advice. I just want to confirm before making cuts. > I plan on cutting the angles below. I'm not too sure about the walls, > which I plan on cutting at 60deg on each 4'side. > > > > <https://lh3.googleusercontent.com/-kz8qnE3-Uto/U6Bc3jxwvjI/AAAAAAAAAJo/0V2bnhmzLaA/s1600/hex.png> > > > On Monday, June 16, 2014 7:39:41 PM UTC-7, Tiprin Lujan wrote: >> >> Hi everyone, I'll be building my first hexayurt this year, an H12. I was >> hoping to miter the panels to eliminate some of the sunlight gaps that are >> caused by Danger hinges. I'd love your opinion on this jig I made up. I >> have two different blocks, one cut at 15 deg and one at 30 deg. The idea >> is to screw this long razor blade onto the block and use that as a angle >> cutting jig. The back of the block is straight and flat so I can clamp a >> guide fence to the panel for a straight cut. What do ya think? >> >> >> >> <https://lh3.googleusercontent.com/-BkBDWw1DRHI/U5-o7v6JhVI/AAAAAAAAAJM/Aj5Iv3SoGUo/s1600/IMAG0828%5B1%5D.jpg> >> >> >> <https://lh3.googleusercontent.com/-p9Phv8jHY6A/U5-pGatqqfI/AAAAAAAAAJU/dKoJnjlAILY/s1600/IMAG0827%5B1%5D.jpg> >> >> >> <https://lh6.googleusercontent.com/-m0EHPapRFZ4/U5-oxA8eF8I/AAAAAAAAAJE/wS_Fd8uDl4E/s1600/IMAG0829%5B1%5D.jpg> >> >> > On Monday, June 16, 2014 7:39:41 PM UTC-7, Tiprin Lujan wrote: >> >> Hi everyone, I'll be building my first hexayurt this year, an H12. I was >> hoping to miter the panels to eliminate some of the sunlight gaps that are >> caused by Danger hinges. I'd love your opinion on this jig I made up. I >> have two different blocks, one cut at 15 deg and one at 30 deg. The idea >> is to screw this long razor blade onto the block and use that as a angle >> cutting jig. The back of the block is straight and flat so I can clamp a >> guide fence to the panel for a straight cut. What do ya think? >> >> >> >> <https://lh3.googleusercontent.com/-BkBDWw1DRHI/U5-o7v6JhVI/AAAAAAAAAJM/Aj5Iv3SoGUo/s1600/IMAG0828%5B1%5D.jpg> >> >> >> <https://lh3.googleusercontent.com/-p9Phv8jHY6A/U5-pGatqqfI/AAAAAAAAAJU/dKoJnjlAILY/s1600/IMAG0827%5B1%5D.jpg> >> >> >> <https://lh6.googleusercontent.com/-m0EHPapRFZ4/U5-oxA8eF8I/AAAAAAAAAJE/wS_Fd8uDl4E/s1600/IMAG0829%5B1%5D.jpg> >> >> > On Monday, June 16, 2014 7:39:41 PM UTC-7, Tiprin Lujan wrote: >> >> Hi everyone, I'll be building my first hexayurt this year, an H12. I was >> hoping to miter the panels to eliminate some of the sunlight gaps that are >> caused by Danger hinges. I'd love your opinion on this jig I made up. I >> have two different blocks, one cut at 15 deg and one at 30 deg. The idea >> is to screw this long razor blade onto the block and use that as a angle >> cutting jig. The back of the block is straight and flat so I can clamp a >> guide fence to the panel for a straight cut. What do ya think? >> >> >> >> <https://lh3.googleusercontent.com/-BkBDWw1DRHI/U5-o7v6JhVI/AAAAAAAAAJM/Aj5Iv3SoGUo/s1600/IMAG0828%5B1%5D.jpg> >> >> >> <https://lh3.googleusercontent.com/-p9Phv8jHY6A/U5-pGatqqfI/AAAAAAAAAJU/dKoJnjlAILY/s1600/IMAG0827%5B1%5D.jpg> >> >> >> <https://lh6.googleusercontent.com/-m0EHPapRFZ4/U5-oxA8eF8I/AAAAAAAAAJE/wS_Fd8uDl4E/s1600/IMAG0829%5B1%5D.jpg> >> >> -- > You received this message because you are subscribed to the Google Groups > "hexayurt" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To post to this group, send email to [email protected]. > Visit this group at http://groups.google.com/group/hexayurt. > For more options, visit https://groups.google.com/d/optout. > -- You received this message because you are subscribed to the Google Groups "hexayurt" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To post to this group, send email to [email protected]. Visit this group at http://groups.google.com/group/hexayurt. For more options, visit https://groups.google.com/d/optout.
