And this is my BFD mod with its cut list which has all possible cuts for a stretch yurt with a large vertical wall for a full size door:
http://www.appropedia.org/BFD_mod (I do call 60 degree cut a "30 degree" and use "15 degree" for the roof piramid). Cheers, Vladimir On Tue, Jun 17, 2014 at 11:04 AM, Vladimir Khodel <[email protected]> wrote: > I did 60 degrees everywhere ie beveled top of the walls in as well. Foam > does not like being cut at sharp angles, so 30 degree may not come out > well... > On Jun 17, 2014 8:23 AM, "Tiprin Lujan" <[email protected]> wrote: > >> Great! Thanks for the advice. I just want to confirm before making cuts. >> I plan on cutting the angles below. I'm not too sure about the walls, >> which I plan on cutting at 60deg on each 4'side. >> >> >> >> <https://lh3.googleusercontent.com/-kz8qnE3-Uto/U6Bc3jxwvjI/AAAAAAAAAJo/0V2bnhmzLaA/s1600/hex.png> >> >> >> On Monday, June 16, 2014 7:39:41 PM UTC-7, Tiprin Lujan wrote: >>> >>> Hi everyone, I'll be building my first hexayurt this year, an H12. I was >>> hoping to miter the panels to eliminate some of the sunlight gaps that are >>> caused by Danger hinges. I'd love your opinion on this jig I made up. I >>> have two different blocks, one cut at 15 deg and one at 30 deg. The idea >>> is to screw this long razor blade onto the block and use that as a angle >>> cutting jig. The back of the block is straight and flat so I can clamp a >>> guide fence to the panel for a straight cut. What do ya think? >>> >>> >>> >>> <https://lh3.googleusercontent.com/-BkBDWw1DRHI/U5-o7v6JhVI/AAAAAAAAAJM/Aj5Iv3SoGUo/s1600/IMAG0828%5B1%5D.jpg> >>> >>> >>> <https://lh3.googleusercontent.com/-p9Phv8jHY6A/U5-pGatqqfI/AAAAAAAAAJU/dKoJnjlAILY/s1600/IMAG0827%5B1%5D.jpg> >>> >>> >>> <https://lh6.googleusercontent.com/-m0EHPapRFZ4/U5-oxA8eF8I/AAAAAAAAAJE/wS_Fd8uDl4E/s1600/IMAG0829%5B1%5D.jpg> >>> >>> >> On Monday, June 16, 2014 7:39:41 PM UTC-7, Tiprin Lujan wrote: >>> >>> Hi everyone, I'll be building my first hexayurt this year, an H12. I was >>> hoping to miter the panels to eliminate some of the sunlight gaps that are >>> caused by Danger hinges. I'd love your opinion on this jig I made up. I >>> have two different blocks, one cut at 15 deg and one at 30 deg. The idea >>> is to screw this long razor blade onto the block and use that as a angle >>> cutting jig. The back of the block is straight and flat so I can clamp a >>> guide fence to the panel for a straight cut. What do ya think? >>> >>> >>> >>> <https://lh3.googleusercontent.com/-BkBDWw1DRHI/U5-o7v6JhVI/AAAAAAAAAJM/Aj5Iv3SoGUo/s1600/IMAG0828%5B1%5D.jpg> >>> >>> >>> <https://lh3.googleusercontent.com/-p9Phv8jHY6A/U5-pGatqqfI/AAAAAAAAAJU/dKoJnjlAILY/s1600/IMAG0827%5B1%5D.jpg> >>> >>> >>> <https://lh6.googleusercontent.com/-m0EHPapRFZ4/U5-oxA8eF8I/AAAAAAAAAJE/wS_Fd8uDl4E/s1600/IMAG0829%5B1%5D.jpg> >>> >>> >> On Monday, June 16, 2014 7:39:41 PM UTC-7, Tiprin Lujan wrote: >>> >>> Hi everyone, I'll be building my first hexayurt this year, an H12. I was >>> hoping to miter the panels to eliminate some of the sunlight gaps that are >>> caused by Danger hinges. I'd love your opinion on this jig I made up. I >>> have two different blocks, one cut at 15 deg and one at 30 deg. The idea >>> is to screw this long razor blade onto the block and use that as a angle >>> cutting jig. The back of the block is straight and flat so I can clamp a >>> guide fence to the panel for a straight cut. What do ya think? >>> >>> >>> >>> <https://lh3.googleusercontent.com/-BkBDWw1DRHI/U5-o7v6JhVI/AAAAAAAAAJM/Aj5Iv3SoGUo/s1600/IMAG0828%5B1%5D.jpg> >>> >>> >>> <https://lh3.googleusercontent.com/-p9Phv8jHY6A/U5-pGatqqfI/AAAAAAAAAJU/dKoJnjlAILY/s1600/IMAG0827%5B1%5D.jpg> >>> >>> >>> <https://lh6.googleusercontent.com/-m0EHPapRFZ4/U5-oxA8eF8I/AAAAAAAAAJE/wS_Fd8uDl4E/s1600/IMAG0829%5B1%5D.jpg> >>> >>> -- >> You received this message because you are subscribed to the Google Groups >> "hexayurt" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> To post to this group, send email to [email protected]. >> Visit this group at http://groups.google.com/group/hexayurt. >> For more options, visit https://groups.google.com/d/optout. >> > -- You received this message because you are subscribed to the Google Groups "hexayurt" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To post to this group, send email to [email protected]. Visit this group at http://groups.google.com/group/hexayurt. For more options, visit https://groups.google.com/d/optout.
