Jigsaw. Most of them have an adjustable angle, up to 45 degrees. I used this one, $40: http://www.homedepot.com/p/Ryobi-4-8-Amp-Variable-Speed-Jigsaw-JS481L/202854039 The angle adjustment came loose in the process of making the yurt, purchased new for it. Fortunately, it was easy to take the bottom plate off, and tighten the relevant nut.
For the angles that were marked on the saw, I just used that - 45 and 15 degrees. For the 38 degree cut, I used a protractor, lined up with the seam on the front of the saw, and the blade. It was kind of awkward, but it doesn't need to be perfect - it works without any beveling. You can just line your cuts up to where the blade will go through, but I found it worked very well to use a guide board (to keep the line straight, instead of just using a chalked line), and a caliper to set the distance from the edge to the guide board - mostly because it was quicker than setting the distance with the saw itself, but I think also more accurate. I used my caliper to measure the distance from the edge of the saw base to the near side of the blade, so it would just barely not cut any off of the top side of the foil. I think the straightness you gain with a guide board is probably a lot more important if you're going to take the time to bevel. And you can get a 10' board from Home Depot for $7 (just check it for straightness against the floor). I had somebody stand on that board while I was cutting, which meant I needed another similar board underneath for support - but I already had it around. It probably would've been worth getting a couple saw horses, to reduce all the bending needed for the cuts. And that would have allowed me to clamp the guide board on. Initially, I duct taped the guide board in place, but after sitting in my barn for a while, I guess with the extra heat, peeling the duct tape off was removing foil. A lot of this info is on http://www.chaosreigns.com/burningman/h8yurt/ On 08/07, Natalie Spilger wrote: > Darxus, > > How did you bevel the edges. That is so cool and I really want to do it, > but cannot find a efficient solution. > > ~ Natalie > > On Thursday, August 7, 2014 7:25:03 AM UTC-7, Darxus wrote: > > On 08/07, Vinay Gupta (Hexayurt Shelter Project) wrote: > > I think we should probably put that on the wiki. I've been > generically > > anti-pyramid for a while, and actually we really should have > documented > > them and put it up too. > > I'm interested in hearing more about that opinion. I was originally > planning to do an H12, but then was asked to use less space for myself, > in > a camp along the esplanade, which I feel is reasonable. Plus, perfect > wood > floor from packing material. > > I feel like all my friends are building 6' stretch hexayurts. > > On 08/07, Lucas González wrote: > > you mean http://www.appropedia.org/Hexayurt_H8 ? > > Thanks, I'll fill this out (and link it from the existing heading on > http://www.appropedia.org/Hexayurt_playa )? > > -- > You received this message because you are subscribed to the Google Groups > "hexayurt" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To post to this group, send email to [email protected]. > Visit this group at http://groups.google.com/group/hexayurt. > For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "hexayurt" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To post to this group, send email to [email protected]. Visit this group at http://groups.google.com/group/hexayurt. For more options, visit https://groups.google.com/d/optout.
