Setting cl_rate in your config.cfg is pointless. It's not really a CVar. It is, but it doesn't respond well to being placed in a config file. Most likely, to get the setting to stick, you'll have to change it in the console after every map load.
Besides, it's not likely that's what the issue is. On Tue, May 20, 2008 at 10:11 AM, Bento de Gier <[EMAIL PROTECTED]> wrote: > I traced some server's i play alot. Both Dutch and UK servers. I have about > 8 to 9 hops to the UK (Amsterdam-London) and a good 6 to 9 hops to server's > in my own country (The Netherlands, Amsterdam hosted). I do have to say > that > my ISP added a lot of hops in the past few years. I used to have like 6 > hops > to any network in The Netherlands and now I sometimes have 9. > > Nakin, you're saying that 20,55,66 or 111 fps makes you shoot faster but > run > slower? I know that developer 1 makes you run slower. > > I will try these values now: > > > rate 20000 > cl_updaterate "100" > cl_cmdrate "100" > ex_interp "0.01" > cl_rate 20000 > fps_max "101" > > I'll let you know if it made any difference. Further suggestions are more > than welcome! > > Cheers, > > Bento > > -----Oorspronkelijk bericht----- > Van: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] Namens AnAkIn . > Verzonden: dinsdag 20 mei 2008 12:48 > Aan: Half-Life dedicated Linux server mailing list > Onderwerp: Re: [hlds_linux] HL1 Client Problems > > Yes, rate is max 20000. > > cl_updaterate should be 100 if you use ex_interp 0.01 > > cl_cmdrate should be maximum 100 if you get 100 FPS, it doesn't send more > command packets than FPS. > > cl_resend has nothing to do with netcode. > > cl_cmdbackup should stay at 2. > > cl_rate could be set to 20000 but I doubt it would make a noticeable > difference. > > I don't think you problem is related to netcode settings though...:S > > The guns shooting slower have probably to do with your FPS. > > There are some FPS values where you can shoot faster, run faster, etc. > > Example: > > Shoot faster (from memory, there are more values) : 20,50,66,111 > > Higher FPS makes you run slower afaik (no special value) > > Higher FPS makes you surf faster (surf_ maps) > > Higher FPS makes you jump slower > > > -----Oorspronkelijk bericht----- > Van: Quickcut.concrete [mailto:[EMAIL PROTECTED] > Verzonden: dinsdag 20 mei 2008 12:55 > Aan: [EMAIL PROTECTED] > Onderwerp: RE: [hlds_linux] HL1 Client Problems > > Do a cmd tracert to the servers your playing on and you will probably > find > your getting lots of hops to the server this can cause hit reg issues. > Common with adsl you might find another isp will give you better luck > > > 2008/5/20 Bento de Gier <[EMAIL PROTECTED]>: > > > I don't know if this is really a good place to post this but there are a > > lot > > more techies on here then on the Steam forums J > > > > > > > > > > > > I've been playing CS and CS:CZ for about 4 years now and never had really > > bad issues with bullet registration etc. but now I have. I have problems > > with the bullet reg in CS:CZ for ages now (after the big steam friends > > update I think). Let me give you a bit background info: > > > > > > > > CS 1.6 runs fine and on a decent (boosted?) server I can play like I > > normally would and I'm able to hit people very good. When I switch over > to > > CS:CZ the whole game feels like a big sponge. A great percentage of my > > fired > > bullets seem not to register while other players kill me with only a few > > bullets as I can do on CS 1.6. Also my guns appear to shoot slower than > > normal. It's becoming a bloody nightmare as I play CZ competitively. I > have > > exactly the same config settings on CZ as I have on CS. > > > > > > > > I have an Intel E6850 (Dualcore 2x 3Ghz) with 4 GB of ram and a GeForce > > 8600 > > GTS all plumbed into an Asus P5K-E motherboard. My PC is hooked up to a > > Linksys router which is connected to the Dutch DSL network. I have 3072 > > kbit > > downloadspeed and 700something kbit upload speed. (I do live ~3 km's from > > the connection point where all house's are interconnected.) > > > > > > > > My netcode settings are: > > > > Rate 20000 (Everything above 20k is useless so I have been told) > > > > Cl_updaterate 101 > > > > Cl_cmdrate 106 > > > > Ex_interp 0.01 (or 0.1 but that makes no difference to my problem) > > > > Cl_resend 2 (default) > > > > Cl_cmdbackup 2 (default) > > > > Cl_rate 9999 (default) > > > > > > > > I normally get a constant 100 fps and sometimes a bit of choke <10. > > > > > > > > > > > > I'm really lost here and don't really don't know what to do about this. > All > > suggestions are welcome ;-) > > > > > > > > Met vriendelijke groet, > > > > With Kind Regards, > > > > > > > > Bento de Gier > > > > <mailto:[EMAIL PROTECTED]> [EMAIL PROTECTED] > > > > _______________________________________________ > > To unsubscribe, edit your list preferences, or view the list archives, > > please visit: > > http://list.valvesoftware.com/mailman/listinfo/hlds_linux > > > _______________________________________________ > To unsubscribe, edit your list preferences, or view the list archives, > please visit: > http://list.valvesoftware.com/mailman/listinfo/hlds_linux > > > _______________________________________________ > To unsubscribe, edit your list preferences, or view the list archives, > please visit: > http://list.valvesoftware.com/mailman/listinfo/hlds_linux > -- -Richard Eid _______________________________________________ To unsubscribe, edit your list preferences, or view the list archives, please visit: http://list.valvesoftware.com/mailman/listinfo/hlds_linux
