Then it's likely not a card but a network problem. Asymmetric routing maybe?
Do you get any errors when you try to connect?
On 11/09/2007, James M < [EMAIL PROTECTED]> wrote:
>
> ping works!
>
> On 9/10/07, Ivica Brodaric < [EMAIL PROTECTED]> wrote:
> > That should be OK. Try to ping the IP address from the PC. Do traceroute
> if
> > you can't ping.
> >
> >
> > On 11/09/2007, James M < [EMAIL PROTECTED]> wrote:
> > > I do not have access to all the os's that run in each lpar so I did
> > > everything from the HMC.
> > > I higlighted each image one by one and configured the channel path
> off.
> > > I again highlighted each image and this time configured the channel
> > online.
> > > FYI - the only image that is actually using the ICC chpid is the vm
> > > 5.2 system which I do have access to.
> > > -jim
> > > On 9/10/07, Ivica Brodaric <[EMAIL PROTECTED]> wrote:
> > > > Let's be clear. On all LPARs:
> > > >
> > > > CP VARY OFF PATH xx FROM ALL
> > > > CP VARY OFF CHPID xx
> > > >
> > > > Then on each LPAR:
> > > >
> > > > CP VARY ON CHPID xx
> > > >
> > > > Did you do that?
> > > >
> > > >
> > > > On 11/09/2007, James M < [EMAIL PROTECTED]> wrote:
> > > > > OK thanks. I varied all off first and the all on.
> > > > > I saw all the devices go off and come back online on operx.
> > > > > ...but it didn't help - I still cannot connect from the pc to the
> icc
> > > > port.
> > > > > I did enable the console cuu before trying.
> > > > >
> > > > > On 9/10/07, Ivica Brodaric < [EMAIL PROTECTED]> wrote:
> > > > > > Yes. It has to be offline to all LPARs in order to reset itself.
> > > > > >
> > > > > >
> > > > > > On 11/09/2007, James M < [EMAIL PROTECTED]> wrote:
> > > > > > > maybe we're getting someplace.
> > > > > > > are you suggesting that I have to config path off in all the
> lpars
> > and
> > > > > > > then config it on in all?
> > > > > > > what I did was off/on in lpar 1 - off/on lpar2 and so on.
> > > > > > >
> > > > > > >
> > > > > > > On 9/10/07, Ivica Brodaric < [EMAIL PROTECTED]> wrote:
> > > > > > > > Did you vary it offline from all LPARs at the same time?
> > > > > > > >
> > > > > > > >
> > > > > > > > On 11/09/2007, James M <[EMAIL PROTECTED]> wrote:
> > > > > > > > > I did try toggling the chpid off/on in each of the lpars
> but
> > I'm
> > > > not
> > > > > > > > > sure it worked properly.
> > > > > > > > > it went from online/online to online/standby. I never did
> see
> > the
> > > > > > > > > current state go to offline!
> > > > > > > > >
> > > > > > > > > On 9/10/07, Rich Smrcina < [EMAIL PROTECTED] > wrote:
> > > > > > > > > > Resetting the ICC port will only affect the ICC users,
> if
> > most
> > > > of
> > > > > > your
> > > > > > > > > > users are coming in through VM's TCP/IP stack, it's not
> > using
> > > > the
> > > > > > ICC.
> > > > > > > > > > If only your console or datacenter users use the ICC,
> you
> > can
> > > > reset
> > > > > > it
> > > > > > > > > > without affecting your users.
> > > > > > > > > >
> > > > > > > > > > James M wrote:
> > > > > > > > > > > device shows enabled.
> > > > > > > > > > > I cannot reset the port on the hmc since it's a dual
> port
> > card
> > > > > > (icc &
> > > > > > > > > > > tcpip) and that would mean dropping many vm & os
> telnet
> > > > clients.
> > > > > > > > > > >
> > > > > > > > > > > On 9/10/07, David Kreuter <[EMAIL PROTECTED] >
> > wrote:
> > > > > > > > > > >>
> > > > > > > > > > >>
> > > > > > > > > > >> from the hmc try resetting the OSA port at the chpid
> > level.
> > > > > > > > > > >> David
> > > > > > > > > > >>
> > > > > > > > > > >> ______________________________ __
> > > > > > > > > > >> From: The IBM z/VM Operating System on behalf of
> James M
> > > > > > > > > > >> Sent: Mon 9/10/2007 10:47 AM
> > > > > > > > > > >> To: [email protected]
> > > > > > > > > > >> Subject: [IBMVM] z/VM 5.2 ICC console connection
> problems
> > > > > > > > > > >>
> > > > > > > > > > >>
> > > > > > > > > > >>
> > > > > > > > > > >>
> > > > > > > > > > >> Over the weekend an operator "I did something..I
> don't
> > know
> > > > what"
> > > > > > > > that
> > > > > > > > > > >> has rendered the ICC vm console unusable.
> > > > > > > > > > >> I tried disable/enable cuu, vary off/on path to cuu
> and
> > > > dropping
> > > > > > the
> > > > > > > > > > >> session from the HMC ICC utilities menu all to no
> avail.
> > > > > > > > > > >> Can someone please suggest other possible solutions.
> > Thanks
> > > > > > > > > > >> -Jim
> > > > > > > > > > >>
> > > > > > > > > > >>
> > > > > > > > > > >
> > > > > > > > > >
> > > > > > > > > > --
> > > > > > > > > > Rich Smrcina
> > > > > > > > > > VM Assist, Inc.
> > > > > > > > > > Phone: 414-491-6001
> > > > > > > > > > Ans Service: 360-715-2467
> > > > > > > > > > rich.smrcina at vmassist.com
> > > > > > > > > > http://www.linkedin.com/in/richsmrcina
> > > > > > > > > >
> > > > > > > > > > Catch the WAVV! http://www.wavv.org
> > > > > > > > > > WAVV 2008 - Chattanooga - April 18-22, 2008
> > > > > > > > > >
> > > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > > > >
> > > > > >
> > > > > >
> > > > >
> > > >
> > > >
> > >
> >
> >
>
