I do not have access to all the os's that run in each lpar so I did
everything from the HMC.
I higlighted each image one by one and configured the channel path off.
I again highlighted each image and this time configured the channel online.
FYI - the only image that is actually using the ICC chpid is the vm
5.2 system which I do have access to.
-jim
On 9/10/07, Ivica Brodaric <[EMAIL PROTECTED]> wrote:
> Let's be clear. On all LPARs:
>
> CP VARY OFF PATH xx FROM ALL
> CP VARY OFF CHPID xx
>
> Then on each LPAR:
>
> CP VARY ON CHPID xx
>
> Did you do that?
>
>
> On 11/09/2007, James M <[EMAIL PROTECTED]> wrote:
> > OK thanks. I varied all off first and the all on.
> > I saw all the devices go off and come back online on operx.
> > ...but it didn't help - I still cannot connect from the pc to the icc
> port.
> > I did enable the console cuu before trying.
> >
> > On 9/10/07, Ivica Brodaric < [EMAIL PROTECTED]> wrote:
> > > Yes. It has to be offline to all LPARs in order to reset itself.
> > >
> > >
> > > On 11/09/2007, James M < [EMAIL PROTECTED]> wrote:
> > > > maybe we're getting someplace.
> > > > are you suggesting that I have to config path off in all the lpars and
> > > > then config it on in all?
> > > > what I did was off/on in lpar 1 - off/on lpar2 and so on.
> > > >
> > > >
> > > > On 9/10/07, Ivica Brodaric <[EMAIL PROTECTED]> wrote:
> > > > > Did you vary it offline from all LPARs at the same time?
> > > > >
> > > > >
> > > > > On 11/09/2007, James M <[EMAIL PROTECTED]> wrote:
> > > > > > I did try toggling the chpid off/on in each of the lpars but I'm
> not
> > > > > > sure it worked properly.
> > > > > > it went from online/online to online/standby. I never did see the
> > > > > > current state go to offline!
> > > > > >
> > > > > > On 9/10/07, Rich Smrcina < [EMAIL PROTECTED] > wrote:
> > > > > > > Resetting the ICC port will only affect the ICC users, if most
> of
> > > your
> > > > > > > users are coming in through VM's TCP/IP stack, it's not using
> the
> > > ICC.
> > > > > > > If only your console or datacenter users use the ICC, you can
> reset
> > > it
> > > > > > > without affecting your users.
> > > > > > >
> > > > > > > James M wrote:
> > > > > > > > device shows enabled.
> > > > > > > > I cannot reset the port on the hmc since it's a dual port card
> > > (icc &
> > > > > > > > tcpip) and that would mean dropping many vm & os telnet
> clients.
> > > > > > > >
> > > > > > > > On 9/10/07, David Kreuter <[EMAIL PROTECTED] > wrote:
> > > > > > > >>
> > > > > > > >>
> > > > > > > >> from the hmc try resetting the OSA port at the chpid level.
> > > > > > > >> David
> > > > > > > >>
> > > > > > > >> ______________________________ __
> > > > > > > >> From: The IBM z/VM Operating System on behalf of James M
> > > > > > > >> Sent: Mon 9/10/2007 10:47 AM
> > > > > > > >> To: [email protected]
> > > > > > > >> Subject: [IBMVM] z/VM 5.2 ICC console connection problems
> > > > > > > >>
> > > > > > > >>
> > > > > > > >>
> > > > > > > >>
> > > > > > > >> Over the weekend an operator "I did something..I don't know
> what"
> > > > > that
> > > > > > > >> has rendered the ICC vm console unusable.
> > > > > > > >> I tried disable/enable cuu, vary off/on path to cuu and
> dropping
> > > the
> > > > > > > >> session from the HMC ICC utilities menu all to no avail.
> > > > > > > >> Can someone please suggest other possible solutions. Thanks
> > > > > > > >> -Jim
> > > > > > > >>
> > > > > > > >>
> > > > > > > >
> > > > > > >
> > > > > > > --
> > > > > > > Rich Smrcina
> > > > > > > VM Assist, Inc.
> > > > > > > Phone: 414-491-6001
> > > > > > > Ans Service: 360-715-2467
> > > > > > > rich.smrcina at vmassist.com
> > > > > > > http://www.linkedin.com/in/richsmrcina
> > > > > > >
> > > > > > > Catch the WAVV! http://www.wavv.org
> > > > > > > WAVV 2008 - Chattanooga - April 18-22, 2008
> > > > > > >
> > > > > >
> > > > >
> > > > >
> > > >
> > >
> > >
> >
>
>
