Hello Andy, I have another set of IntelS5000XAL machines. I used "pefconfig" util to populate the PEF table entries, but still I am unable to receive the PETraps for power off/on events or in general trap for any IPMI events. Though I have set the lan alert destination and the "alert immediate" IPMI command is working and its traps are also being received.
It seems that the PEF Alert Policy is not getting populated. I am using " ./pefconfig -F lan2 -N ipmi -U "" -P "ab1234" -r -A 10.0.0.73" command to configure PEF, and, " ./ipmitool -I lanp -H 10.0.100.218 -U "" -P "ab1234" -C 0 -o intelplus event "Pwr Unit Stat" "Power off/down" assert" command to generate an IPMI event. What is the correct way to configure the BMC for sending out Lan alerts? Am I missing someting here? For your referenece, following is the log of "pefconfig" and "ipmitool" commands: [EMAIL PROTECTED] util]# ./pefconfig -F lan2 -N ipmi -U "" -P "ab1234" -r -A 10.0.0.73 pefconfig ver 1.59 Opening connection to node ipmi ... -- BMC version 0.55, IPMI version 2.0 ipmi_cmd_lan2 error 204 ipmi_cmd_lan2 error 204 ipmi_cmd_lan2 error 204 ipmi_cmd_lan2 error 204 ipmi_cmd_lan2 error 204 pefconfig: GetPefEntry ... PEFilter(01): 01 Temperature Sensor event - enabled for alert PEFilter(02): 02 Voltage Sensor event - enabled for alert PEFilter(03): 04 Fan Failure event - enabled for alert PEFilter(04): 05 Chassis Intrusion event - enabled for alert PEFilter(05): 08 Power Supply Fault event - enabled for alert PEFilter(06): 0c Memory ECC Error event - enabled for alert PEFilter(07): 0f FRB Failure event - enabled for alert PEFilter(08): 07 BIOS POST Error event - enabled for alert PEFilter(09): 13 Fatal NMI event - enabled for alert PEFilter(10): 23 Watchdog Timer Reset event - enabled for alert PEFilter(11): 12 System Restart event - enabled for alert PEFilter(12): 20 OS Critical Stop event - enabled for alert PEFilter(13): 02 Power Redundancy Lost event - enabled for alert PEF Control: 00 PEF Actions: 2f Alert PwrDn Reset PwrCyc DiagInt PEF Startup Delay: 60 sec PEF Alert Startup Delay: 60 sec PEF Alert Policy[1]: 01 00 00 00 Disabled PEF Alert Policy[2]: 02 00 00 00 Disabled PEF Alert Policy[3]: 03 00 00 00 Disabled PEF Alert Policy[4]: 04 00 00 00 Disabled pefconfig: GetLanEntry for channel 1 ... Lan Param(0) Set in progress: 00 Lan Param(1) Auth type support: 15 None MD5 Pswd Lan Param(2) Auth type enables: 00 00 00 15 00 Lan Param(3) IP address: 10 0 100 218 Lan Param(4) IP addr src: 01 Static Lan Param(5) MAC addr: 00 04 23 d4 1c 1a Lan Param(6) Subnet mask: 255 255 0 0 Lan Param(7) IPv4 header: 40 40 10 Lan Param(10) BMC grat ARP : 01 Lan Param(11) grat ARP interval: 05 Lan Param(12) Def gateway IP: 10 0 0 2 Lan Param(13) Def gateway MAC: 00 00 00 00 00 00 Lan Param(14) Sec gateway IP: 0 0 0 0 Lan Param(15) Sec gateway MAC: 00 00 00 00 00 00 Lan Param(16) Community string: public Lan Param(17) Num dest: 04 Lan Param(18) Dest type: 01 00 00 00 00 Lan Param(18) Dest type: 02 00 00 00 00 Lan Param(18) Dest type: 03 00 00 00 00 Lan Param(18) Dest type: 04 00 00 00 00 Lan Param(19) Dest address: 01 00 00 [0 0 0 0] 00 00 00 00 00 00 Lan Param(19) Dest address: 02 00 00 [0 0 0 0] 00 00 00 00 00 00 Lan Param(19) Dest address: 03 00 00 [0 0 0 0] 00 00 00 00 00 00 Lan Param(19) Dest address: 04 00 00 [0 0 0 0] 00 00 00 00 00 00 Lan Param(192) DHCP Server IP: 0 0 0 0 Lan Param(193) DHCP MAC Address: 00 00 00 00 00 00 Lan Param(194) DHCP Enable: 00 GetChanAcc(lan), ret = 0, new value = 0a Access = Always Avail, PEF Alerts Enabled Channel Access Mode(Lan): 0a 04 GetSOL for channel 1 ... SOL Enable: 00 SOL Auth: 02 SOL Accum Interval: 04 32 SOL Retry Interval: 06 14 SOL nvol Baud Rate: 07 19.2k SOL vol Baud Rate: 00 nobaud Get User Access(1): 0f 02 01 34 IPMI, Admin () Get User Access(2): 0f 02 01 34 IPMI, Admin (admin) Get User Access(3): 0f 02 01 0f No access () Get User Access(4): 0f 02 01 0f No access () [EMAIL PROTECTED] src]# ./ipmitool -I lanp -H 10.0.100.218 -U "" -P "ab1234" -C 0 -o intelplus event "Pwr Unit Stat" "Power off/down" assert Finding sensor Pwr Unit Stat... ok 0 | Pre-Init Time-stamp | Power Unit Pwr Unit Stat | Power off/down | Asserted [EMAIL PROTECTED] src]# Best Regards, Sanjay --- "Cress, Andrew R" <[EMAIL PROTECTED]> wrote: > Sanjay, > > The IPMI SEL should log those events, BUT ... the > sensors for each > platform can be configured at the factory to log or > not log events via a > setting in its SDR. This is normally written out in > the initial SDR > settings at the factory. Every platform I've ever > tested does have a > SEL event for power off/on, etc. HP should be able > to give more > information as to how this is set or changed in the > SDR. > > For a PET, IPMI systems usually have some default > PEF table entries to > generate PETraps, but I don't know what those are > for HP Proliant. > You can view them with "ipmiutil lan" or "pefconfig" > from > http://ipmiutil.sf.net. > If these events are not covered by the factory > default PEF entries, you > could compose a custom PEF table entry to report > this, but the SDR would > have to have the eventing enabled for that sensor as > mentioned above. > > Andy > > -----Original Message----- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] > On Behalf Of > sanjay verma > Sent: Tuesday, February 13, 2007 7:48 AM > To: ipmitool-devel@lists.sourceforge.net > Subject: [Ipmitool-devel] HP ProLiant power > off/on/reset events > > Greetings, > > I am using HP ProLiant systems and ipmitool-1.8.8 > and > want to be informed about a power off/on/reset > events > by mining SEL events or by receiving IPMI PET. > > Does IPMI SEL logs such events? I did not see such > events even after issuing several power off/on/reset > commands. > > Does ipmitool support PEF operations to set alert > destination addresses and enable BMCs to sendout PET > for off/on/reset events? > > Regards, > SKV > > > > > ________________________________________________________________________ > ____________ > Bored stiff? Loosen up... > Download and play hundreds of games for free on > Yahoo! Games. > http://games.yahoo.com/games/front > > ------------------------------------------------------------------------ > - > Using Tomcat but need to do more? Need to support > web services, > security? > Get stuff done quickly with pre-integrated > technology to make your job > easier. > Download IBM WebSphere Application Server v.1.0.1 > based on Apache > Geronimo > http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642 > _______________________________________________ > Ipmitool-devel mailing list > Ipmitool-devel@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/ipmitool-devel > ____________________________________________________________________________________ Don't pick lemons. See all the new 2007 cars at Yahoo! Autos. http://autos.yahoo.com/new_cars.html ------------------------------------------------------------------------- Take Surveys. Earn Cash. Influence the Future of IT Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys-and earn cash http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV _______________________________________________ Ipmitool-devel mailing list Ipmitool-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/ipmitool-devel
