On Jan 4, 2006, at 9:03 AM, <[EMAIL PROTECTED]> wrote: > > > --- Keith C <[EMAIL PROTECTED]> wrote: > >> On Jan 4, 2006, at 12:28 AM, John H. wrote: >> >>> ok, i got latest firmware, and it seems sound >> works now, but i cannot >>> change channels, and the picture is really fuzzy. >>> here's the dmesg >>> >>> ivtv: ==================== START INIT IVTV >> ==================== >>> ivtv: version 0.4.1 (tagged release) loading >>> ivtv: Linux version: 2.6.15 preempt K7 gcc-4.0 >>> ivtv: In case of problems please include the >> debug info between >>> ivtv: the START INIT IVTV and END INIT IVTV >> lines, along with >>> ivtv: any module options, when mailing the >> ivtv-users mailinglist. >>> ivtv0: Autodetected WinTV PVR 150 card (cx23416 >> based) >>> ivtv0: i2c attach to card #0 ok [client=tveeprom, >> addr=50] >>> tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver >> #0) >>> ivtv0: i2c attach to card #0 ok [client=(tuner >> unset), addr=61] >> >> Yeah, you're going to have some serious problems, as >> the tuner is not >> being set for your card. >> > Are you absolulty sure of this? I always get this > message but still get video. See this: > > ivtv: ==================== START INIT IVTV > ==================== > ivtv: version 0.4.1 (tagged release) loading > ivtv: Linux version: 2.6.13-gentoo-r3 SMP preempt K7 > gcc-3.4 > ivtv: In case of problems please include the debug > info between > ivtv: the START INIT IVTV and END INIT IVTV lines, > along with > ivtv: any module options, when mailing the ivtv-users > mailinglist. > ivtv0: Autodetected WinTV PVR 250 card (cx23416 based) > ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, > low) -> IRQ 19 > tveeprom: ivtv version > tveeprom: Hauppauge: model = 32032, rev = B326, > serial# = 7109870 > tveeprom: tuner = Temic 4036FY5 (idx = 26, type = 8) > tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = > 0x00001000) > tveeprom: audio processor = MSP4448 (type = 1b) > tveeprom: decoder processor = SAA7115 (type = 13) > ivtv0: i2c attach to card #0 ok [client=tveeprom, > addr=50] > tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c > driver #0 > ivtv0: i2c attach to card #0 ok [client=(tuner unset), > addr=61] > saa7115 0-0021: ivtv driver > saa7115 0-0021: saa7115 found @ 0x42 (ivtv i2c driver > #0) > ivtv0: i2c attach to card #0 ok [client=saa7115, > addr=21] > msp3400 0-0040: ivtv driver > msp3400 0-0040: chip=MSP4448G-A2 +nicam +simple > +simpler +radio mode=simpler > msp3400 0-0040: msp34xxg daemon started > ivtv0: i2c attach to card #0 ok [client=MSP4448G-A2, > addr=40] > ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 > bytes) > ivtv0: Encoder revision: 0x02050032 > ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 > buffers (4096KB total) > ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 > buffers (2048KB total) > ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 > buffers (2048KB total) > ivtv0: Allocate DMA encoder PCM audio stream: 455 x > 4608 buffers (2048KB total) > tuner: type set to 8 (Temic NTSC (4036 FY5)) by ivtv > i2c driver #0 > ivtv0: Initialized WinTV PVR 250, card #0 > ivtv: ==================== END INIT IVTV > ==================== >
Well, your tuner is getting set to type 8 after tveeprom loads and ivtv tells tuner what to set it to. This never happens for John and his stays unset. Also, the line wrap being forced on your emails is pretty annoying. Keith _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
