Hello Hans, > The cause is that the tuner is set to 'radio' mode for some peculiar > reason. Can you add the 'debug=1' module option to the tuner module? > I'd like to see the messages from the tuner module when it loads. If > that doesn't help, then I will need your help to debug into the tuner > module. I've seen reports on this before, but I have never been able to > reproduce it myself. To be honest, I can't imagine what can cause this, > but obviously something is wrong here. You are not using any ivtv or > tuner module options, are you?
I don't use any options for the modules. It is certainly something with the loading process because when the modules load, everything works fine for weeks. Problems only appear at boot. I set the debug option, but I think the info below doesn't provide much. The firmware failed to load again for some reason. I'll try to get more info later. regards, Marcel ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.6.2 (development snapshot compiled on Mon May 8 07:35:43 2006) loading ivtv: Linux version: 2.6.16-1.2111_FC5 686 REGPARM 4KSTACKS gcc-4.1 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge WinTV PVR-350 card (cx23415 based) ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 16 (level, low) -> IRQ 18 ivtv0: Unreasonably low latency timer, setting to 64 (was 32) tveeprom 1-0050: Hauppauge model 48134, rev J347, serial# 7110286 tveeprom 1-0050: tuner model is LG TP18PSB01D (idx 47, type 28) tveeprom 1-0050: TV standards PAL(B/G) (eeprom 0x04) tveeprom 1-0050: audio processor is MSP4418 (idx 25) tveeprom 1-0050: decoder processor is SAA7115 (idx 19) tveeprom 1-0050: has radio, has IR remote tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) nvidia: module license 'NVIDIA' taints kernel. saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #0) saa7127 1-0044: saa7127 found @ 0x88 (ivtv i2c driver #0) msp3400 1-0040: MSP4418G-A2 found @ 0x80 (ivtv i2c driver #0) msp3400 1-0040: MSP4418G-A2 supports nicam and radio, mode is autodetect and autoselect ieee1394: Initialized config rom entry `ip1394' USB Universal Host Controller Interface driver v2.3 sd 0:0:0:0: Attached scsi generic sg0 type 0 firmware_loading_store: unexpected value (0) ivtv0: unable to open firmware v4l-cx2341x-enc.fw ivtv0: did you put the firmware in the hotplug firmware directory? ivtv0 warning: failed loading encoder firmware ivtv0 warning: Error loading firmware -3! ivtv0: Error -3 initializing firmware. ivtv0: Error -12 on initialization ivtv: probe of 0000:00:0d.0 failed with error -12 ivtv: ==================== END INIT IVTV ==================== _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
