On Wed, 2006-06-07 at 08:04 +0200, Hans Verkuil wrote: > Please download the 0.6.3 dev. snapshot here: > http://ivtvdriver.org/viewcvs/ivtv/branches/0.6.tar.gz?view=tar > > Now add the 'newi2c=0' ivtv module option and try again. Let me know if > this fixes your problems.
Unfortunately, it did not. I presume that the latter statement is accomplished by having this line in /etc/modprobe.conf: options ivtv newi2c=0 ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.6.3 (development snapshot compiled on Sat 10 Jun 2006 01:33:42 PM MDT) loading ivtv: Linux version: 2.6.16-1.2122_FC5 686 REGPARM 4KSTACKS gcc-4.1 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 17 (level, low) -> IRQ 18 tveeprom 0-0050: Hauppauge model 26032, rev C199, serial# 8125669 tveeprom 0-0050: tuner model is TCL 2002N 5H (idx 99, type 50) tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 0-0050: audio processor is CX25841 (idx 35) tveeprom 0-0050: decoder processor is CX25841 (idx 28) tveeprom 0-0050: has no radio, has IR remote tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0) ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) cs: IO port probe 0x100-0x3af: excluding 0x170-0x177 0x370-0x377 cs: IO port probe 0x3e0-0x4ff: excluding 0x408-0x40f 0x4d0-0x4d7 cs: IO port probe 0x820-0x8ff: excluding 0x830-0x837 cs: IO port probe 0xc00-0xcf7: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcd7 cs: IO port probe 0xa00-0xaff: clean. ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ieee1394: Initialized config rom entry `ip1394' ivtv0: Encoder revision: 0x02050032 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) tuner 0-0061: type set to 50 (TCL 2002N) ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0: i2c addr 0x44 not found for command 0x40045613! ivtv0: i2c addr 0x44 not found for command 0xc0045627! ivtv0: i2c addr 0x44 not found for command 0x40345622! ivtv0: i2c addr 0x44 not found for command 0x40045612! ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0: i2c addr 0x44 not found for command 0x40045613! ivtv0: i2c addr 0x44 not found for command 0x40045612! ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 ivtv: ==================== END INIT IVTV ==================== And once again, cat /dev/video0 > file.mpg yields an empty file. --Greg _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
